Canon imagePRESS 1135 Series Service Manual page 1116

COPIER> ADJUST> CCD
MTF2MCL MTF VL in main scan way (color) [Back]
Lv.1 Details If moire occurs in the image scanning during installation/scanner unit
replacement, increase the level one at a time.
Input the value on the service label during reader controller PCB
replacement/RAM clear.
Use case • At the installation or replacement of scanner unit if moire occurs
on the read image.
• When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution Make sure to set CCD-CHG2 to "1" beforehand.
Display/adj/set range 0 to 4
0: correction ratio 100 %, 1: 95 %, 2: 90 %, 3: 85 %, 4: 80 %
Default value 0
Related service mode COPIER> ADJUST> CCD> CCD-CHG2
MTFSCL MTF VL in sub scan way (color) [Front]
Lv.1 Details If moire occurs in the image scanning during installation/scanner unit
replacement, increase the level one at a time.
Input the value on the service label during reader controller PCB
replacement/RAM clear.
Use case • At the installation or replacement of scanner unit if moire occurs
on the read image.
• When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution Make sure to set CCD-CHNG to "1" beforehand.
Display/adj/set range 0 to 4
0: correction ratio 100 %, 1: 95 %, 2: 90 %, 3: 85 %, 4: 80 %
Default value 0
Related service mode COPIER> ADJUST> CCD> CCD-CHNG
MTF2SCL MTF VL in sub scan way (color) [back]
Lv.1 Details If moire occurs in the image scanning during installation/scanner unit
replacement, increase the level one at a time.
Input the value on the service label during reader controller PCB
replacement/RAM clear.
Use case • At the installation or replacement of scanner unit if moire occurs
on the read image.
• When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution Make sure to set CCD-CHG2 to "1" beforehand.
Display/adj/set range 0 to 4
0: correction ratio 100 %, 1: 95 %, 2: 90 %, 3: 85 %, 4: 80 %
Default value 0
Related service mode COPIER> ADJUST> CCD> CCD-CHG2
8
Service Mode > COPIER > ADJUST (Adjustment Mode) > CCD
8 Service Mode > COPIER > ADJUST (Adjustment Mode) > CCD
COPIER> ADJUST> CCD
MTFMBW MTF VL in main scan way (B&W) [Front]
Lv.1 Details If moire occurs in the image scanning during installation/scanner unit
replacement, increase the level one at a time.
Input the value on the service label during reader controller PCB
replacement/RAM clear.
Use case • At the installation or replacement of scanner unit if moire occurs
on the read image.
• When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution Make sure to set CCD-CHNG to "1" beforehand.
Display/adj/set range 0 to 4
0: correction ratio 100 %, 1: 95 %, 2: 90 %, 3: 85 %, 4: 80 %
Default value 0
Related service mode COPIER> ADJUST> CCD> CCD-CHNG
MTF2MBW MTF VL in main scan way (B&W) [Back]
Lv.1 Details If moire occurs in the image scanning during installation/scanner unit
replacement, increase the level one at a time.
Input the value on the service label during reader controller PCB
replacement/RAM clear.
Use case • At the installation or replacement of scanner unit if moire occurs
on the read image.
• When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution Make sure to set CCD-CHG2 to "1" beforehand.
Display/adj/set range 0 to 4
0: correction ratio 100 %, 1: 95 %, 2: 90 %, 3: 85 %, 4: 80 %
Default value 0
Related service mode COPIER> ADJUST> CCD> CCD-CHG2
MTFSBW MTF VL in sub scan way (B&W) [Front]
Lv.1 Details If moire occurs in the image scanning during installation/scanner unit
replacement, increase the level one at a time.
Input the value on the service label during reader controller PCB
replacement/RAM clear.
Use case • At the installation or replacement of scanner unit if moire occurs
on the read image.
• When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution Make sure to set CCD-CHNG to "1" beforehand.
Display/adj/set range 0 to 4
0: correction ratio 100 %, 1: 95 %, 2: 90 %, 3: 85 %, 4: 80 %
Default value 0
Related service mode COPIER> ADJUST> CCD> CCD-CHNG
8-173
8-173