Canon imagePRESS 1135 Series Service Manual page 1176

COPIER > OPTION > FNC-SW
KSIZE-SW Chinese paper (K-size PP)support setting
Lv.2 Details Setting to detect/display the Chinese paper (K size paper: 8K, 16K)
Use case When K size paper is used.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution Go through the following: COPIER> OPTION> FNC-SW>
MODEL-SZ; and if MODEL-SZ is 0: this mode is enabled with AB
configuration.
Display/adj/set range 0 to 1
0: Disabled (no support), 1: Enabled (supported)
Default value 0
Related service mode COPIER> OPTION> FNC-SW> MODEL-SZ
Supplement/memo 8K paper: 270 x 390 mm, 16K paper: 270 x 195 mm
ORG-B4 Special PP size setting in DADF mode: B4
Lv.2 Details Setting the size of special paper (B4) that cannot be recognized in
DADF stream scanning mode.
To convert to the specified size for properly formulating image when
the Inch/AB-configuration DADF detects B5 paper.
Use case - Upon request from the user
- In the case of pickup of special paper size original from DEDF
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: JIS B4-R, 1: FOLIO-R
Default value 0
PDF-RDCT PDF reduction seting at received-transfr
Lv.2 Details Setting whether to send with reduced image when retrieving the
received image from IFAX into PDF for e-mail/file transmission.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: following the current setting, 1: image reduction
Default value 0
8
Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > FNC-SW
8 Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > FNC-SW
COPIER > OPTION > FNC-SW
REBOOTSW Restart setting at E240 error occurence
Lv.2 Details Setting whether to reboot in the case of E240 error.
In the case of E240 error, the machine is automatically rebooted due
to the possibility of continuous operation of the drive system while
the spooled print job is cleared.
Print job can be obtained if selecting the setting not to reboot.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution - Do not use this mode under normal conditions.
- Be sure to get approval from the user by telling the possibility of
continuous operation of the drive system in the case of E240 error.
Display/adj/set range 0 to 1
0: reboot, 1: no reboot
Default value 0
Supplement/memo E240 error: communication error between the main controller and the
DC controller.
SJB-UNW Reserve upper limit of secure print job
Lv.2 Details Setting the upper limit for the number of reserved jobs in secure print
job.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: 50 jobs, 1: 90 jobs
Default value 0
WEBV-SW ON/OFF of WebDAV function
Lv.2 Details ON/OFF setting of WebDAV function.
OFF setting can reduce memory use of this equipment. And following
WebDAV-related items are hidden in User Mode.
- Additional Functions> Address Book Settings> Registering
Address> File> Protocol> WebDAV
- Additional Functions> Communications Settings> TX Settings>
Use Chunked Encoding with WebDAV Sending
Use case To reduce memory use of this equipment.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: ON, 1: OFF
Default value 0
Related user mode - Additional Functions> Address Book Settings> Registering
Address> File> Protocol> WebDAV
- Additional Functions> Communications Settings> TX Settings> Use
Chunked Encoding with WebDAV Sending
Supplement/memo WebDAV function is equipped as standard with this equipment.
8-233
8-233