Canon imagePRESS 1135 Series Service Manual page 1221

COPIER > OPTION > NETWORK
LPD-PORT Setting of LPD port number
Lv.2 Details Setting the LPD port number.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 1 to 65535
Default value 515
Supplement/memo LPD port: network port for TCP/IP communication when making
prints through network.
WUEV-SW Setting of sleep notification execution
Lv.2 Details Setting to notify/not to notify the sleep mode to the application
(imageWARE, etc) on the network when shifting to/recovering from
the sleep mode.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: Notify, 1: Not to notify
Default value 0
WUEV-INT Setting of sleep notification interval
Lv.2 Details Setting the interval of sleep notification.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution Go through the following: COPIER> OPTION> NETWORK> WUEV-
SW; and if WUEV-SW is 0: this mode is active if the notification is
enabled.
Display/adj/set range 60 to 65535
Unit 1 second
Default value 600
Related service mode COPIER> OPTION> NETWORK> WUEV-SW
WUEV-POT Port number setting for sleep notificatn
Lv.2 Details Setting port number of the PC to notify the sleep mode.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution Go through the following: COPIER> OPTION> NETWORK> WUEV-
SW; and if WUEV-SW is 0: this mode is active if the notification is
enabled.
Display/adj/set range 1 to 65535
Default value 11427
Related service mode COPIER> OPTION> NETWORK> WUEV-SW
8
Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > NETWORK
8 Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > NETWORK
COPIER > OPTION > NETWORK
WUEV-RTR Setting of sleep notification range
Lv.2 Details Setting the number of available routers to the target for sleep
notification.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution Go through the following: COPIER> OPTION> NETWORK> WUEV-
SW; and if WUEV-SW is 0: this mode is active if the notification is
enabled.
Display/adj/set range 0 to 254
Default value 3
Related service mode COPIER> OPTION> NETWORK> WUEV-SW
WUEN-LIV Recovery time setting after sleep notice
Lv.2 Details Setting the time from the sleep start from network without job
assignment until the mode is shifted to the sleep mode.
Use case To set the startup time after sleep notification.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 10 to 600
Unit 1 second
Default value 15
DHCP-12 ON/OFF of DHCP-option 12 request
Lv.2 Details ON/OFF setting for inquiry of the host name (Option 12) who uses
Option 55 of DHCP.
Selecting OFF can prevent DHCP packet from including Option 12 or
Option 81 under the packet-monitoring network environment.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
Supplement/memo DHCP: Dynamic Host Configuration Protocol
8-278
8-278