Canon imagePRESS 1135 Series Service Manual page 1268

■ NETWORK
COPIER> TEST> NETWORK
PING Network connection check
Lv.1 Details Checking connection between this machine and TCP/IP network
Use case • When checking network connection at the time of installation
• When network connection is faulty
Adj/set/operate method 1) Turn OFF the main power supply.
2) Connect the network cable to this machine, and then turn ON the
main power supply.
3) Inform the system administrator at user's site that installation of
the host machine is complete, and ask for network setting.
4) Inform the system administrator about your checking network
connection, and check remote host address of PING transmission
target.
5) Select the item and enter the remote host address, and then press
OK key and Start key.
OK: Connection is normal. Checking procedure is complete.
NG: Connection failed. Go to step 6) if the cable connection is OK.
If the cable connection is faulty, connect again and then go to step
5).
6) Select the item and enter loopback address, and then press OK
key and Start key.
OK: TCP/IP setting of this machine is normal. Go to step 7) to
check NIC.
NG: TCP/IP setting of this machine is faulty. Go to step 3) to check
the setting again.
7) Select the item and enter the local host address, and then press
OK key.
OK: Network setting of this machine and NIC are normal. Inform
the system administrator that the trouble is due to network
environment and ask for countermeasure.
NG: Connection failure/fault with NIC. Check connection of NIC/
replace NIC.
Display/adjust/set range 0.0.0.0 to 255.255.255.255
OK: when connection is normal, NG: when connection is faulty
Suppliment/memo • Remote host address: IP address of PC terminal in network.
• Loopback address: 127.0.0.1. Checking of TCP/IP with this
machine is available because the signal is returned before NIC.
• NIC: network interface board
• Local host address: IP address of this machine
8
Service Mode > COPIER > TEST (Test Print Mode) > NETWORK
8 Service Mode > COPIER > TEST (Test Print Mode) > NETWORK
COPIER> TEST> NETWORK
IPV6-ADR Setting of PING send address (IPv6)
Lv.1 Details Set the IPv6 address to send PING.
When PING is sent to this address by COPIER> TEST> NETWORK>
PING-IP6, the network connection condition in the IPv6 environment
can be checked.
Caution • Enter a consistent character string as an address of IPv6.
• Enter an address within 39 characters including hexadecimal
numbers (0-9, a-f) and a separator (:).
Related service mode COPIER> TEST> NETWORK> PING-IP6
PING-IP6 PING transmission to IPv6 address
Lv.1 Details Send PING to the address specified by IPV6-ADR.
The network connection condition in the IPv6 environment can be
checked.
Adj/set/operate method Select the item, and then press OK key.
Related service mode COPIER> TEST> NETWORK> IPV6-ADR
IPSECPOL Polling test of IPSec encryption board
Lv.1 Details Executing polling test of IPSec encryption board.
Checking of hardware fault is available.
Use case To check whether or not a hardware fault has occurred to the IPSec
encryption board
Adj/set/operate method Select the item, and then press OK key.
Display/adjust/set range When no failure has occurred: OK
When a failure has occurred: NG (0: The board cannot be
recognized. 1: An error occurred to the result.)
Required time Approx. 3 minutes
IPSECINT Interrupt test of IPSec encryption board
Lv.1 Details Executing interrupt test of IPSec encryption board.
Checking of hardware fault is available.
Use case To check whether or not a hardware fault has occurred to the IPSec
encryption board
Adj/set/operate method Select the item, and then press OK key.
Display/adjust/set range When no failure has occurred: OK
When a failure has occurred: NG (0: The board cannot be
recognized. 1: An error occurred to the result.)
Required time Approx. 3 minutes
8-325
T-8-81
8-325