Canon imagePRESS 1135 Series Service Manual page 1164

COPIER> FUNCTION> PART-CHK
MTR Specify operation motor
Lv.1 Details Specify the motor to operate.
Use case At the replacement of the motor / operation check
Adj/set/operate method Enter the value and press the OK key.
Display/adjust/set range 1 to 78
1 to 3: Not used, 4: Primary charging assembly cleaning motor (M4)
5: Primary pre-transfer charging assembly cleaning motor (M5)
6: Drum motor (M6), 7: Drum cleaner motor (M7), 8: ITB motor (M8)
9: ITB steering motor (M9), 10: Fixing belt press motor (M10)
11: Fixing motor (M11)
12: External heat engage/disengage motor (M12)
13: Secondary transfer external roller separation motor (M13)
14: Laser scanner motor (Bk) (M14), 15: POD deck feed motor (M15)
16: Vertical path feed motor (M16), 17: Escape feed motor (M17)
18: Pre-registration feed motor 1 (M18)
19: Pre-registration separation motor 1 (M19)
20: Pre-registration feed motor 2 (M20)
21: Pre-registration separation motor 2 (M21)
22: Pre-registration motor (M22)
23: Pre-registration separation motor (M23)
24: Skew correction motor 1 (M24)
25: Skew correction motor 2 (M25), 26, 27: Not used
28: Pre-fixing feed motor (M28)
29: Pre-fixing feed engage/disengage motor (M29), 30: Not used
31: Delivery switch motor (M31)
32: Straight delivery motor 1 (M32), 33: Not used
34: Delivery decurler motor 1 (M34), 35: Not used
36: Delivery decurler motor 2 (M36), 37: Not used
38: Duplex decurler motor (M38), 39: Not used
40: External delivery motor (M40), 41: Not used
42: Reverse vertical path motor 1 (M42), 43: Not used
44: Reverse vertical path motor 2 (M44)
45: Delivery vertical path motor 1 (M45), 46, 47: Not used
48: Duplex feed motor 1 (M48), 49: Not used
50: Duplex feed motor 2 (M50), 51: Duplex feed motor 3 (M51)
52: Duplex feed motor 4 (M52), 53: Duplex feed motor 5 (M53)
54: Duplex feed motor 6 (M54), 55: Reverse roller motor (M55)
56: Reverse roller switch motor (M56), 57, 58: Not used
59: Delivery vertical path motor 2, 60, 61: Not used
62: Deck feed motor 1 (M62), 63: Deck feed motor 2 (M63)
64: Deck feed motor 3 (M64), 65, 66: Not used
67: Toner container open/close motor (M67), 68: Not used
69: Waste toner stirring motor (M69), 70, 71: Not used
72: Suction belt motor (M72)
73: Pull-out motor (M73), 74, 75: Not used
76: Waste toner feed motor (M76), 77: Not used
78: Escape delivery motor (M78)
During operation: ACTIVE, At termination: OK!
Default value 1
Related service mode COPIER> FUNCTION> PART-CHK> MTR-ON
Supplement/memo The escape delivery motor (M78) exists in the POD deck.
8
Service Mode > COPIER > FUNCTION (Operation / Inspection Mode) > PART-CHK
8 Service Mode > COPIER > FUNCTION (Operation / Inspection Mode) > PART-CHK
COPIER> FUNCTION> PART-CHK
MTR-ON Motor movement checking
Lv.1 Details Start operation check for the motor specified by MTR.
The operation automatically terminates after operation of 5 seconds.
Use case At the replacement of the motor / operation check
Adj/set/operate method Select the item and press the OK key.
Caution When operating the bottle motor, be sure to remove the toner
container. Otherwise, toner leakage may occur in the machine.
Display/adjust/set range During operation: ACTIVE, At termination: OK!
Required time 1 minute
Related service mode COPIER> FUNCTION> PART-CHK> MTR
SL Specify operation solenoid
Lv.1 Details Specify the solenoid to operate.
Use case At the time of replacement of solenoid / operation check
Adj/set/operate method Enter the value and press the OK key.
Display/adjust/set range 1 to 8
1: Patch detection shutter solenoid (SL1)
2: Fixing cleaner solenoid (SL2)
3: Escape switch solenoid (SL3)
4: Not used
5: Deck pickup solenoid (SL5)
6: Deck open/close solenoid (SL6)
7: Not used
8: Fixing separation claw separation solenoid (SL8)
During operation: ACTIVE, At termination: OK!
Default value 1
Related service mode COPIER> FUNCTION> PART-CHK> SL-ON
SL-ON Operation check of solenoid
Lv.1 Details Start operation check for the solenoid specified by SL.
The operation stops after "ON for 0.5sec" => "OFF for 10sec" => "ON
for 0.5sec" => "OFF for 10sec" => "ON for 0.5sec".
Use case At the time of replacement of solenoid / operation check
Adj/set/operate method Select the item and press the OK key.
Display/adjust/set range During operation: ACTIVE, At termination: OK!
Required time 1 minute
Related service mode COPIER> FUNCTION> PART-CHK> SL
DECK-LED LED light check of host deck storage
Lv.1 Details Forcibly turn on all LEDs of the main unit deck.
When this item is set to 1, all LEDs of the main unit deck are turned
on.
The setting automatically returns to 0 after termination of the service
mode.
Use case To check whether or not a failure occurred to LEDs
Adj/set/operate method Select the item and press the OK key.
Display/adjust/set range 0 or 1
0: LEDs turned off, 1: All LEDs turned on
8-221
T-8-54
8-221