Canon imagePRESS 1135 Series Service Manual page 1128

COPIER> ADJUST> HV-TR
2TR-TGT2 Sec transfer current adj value (Ev 1)
Lv.2 Details To set the target current that is applied to the secondary transfer
inner roller under the condition of absolute moisture ratio from 0.64
3
to 1.72 g/m .
When low-voltage mottled image or toner splash on solid image
occurs, increase the current.
When high-voltage mottled image or density loss due to excessive
transfer occurs, decrease the current.
As the value is changed by 1, current is increased/decreased by
5 uA.
+: Increase
-: Decrease
Use case When image failures occur on all the paper types (mottled image/
density loss due to excessive transfer/toner splash on solid image)
Adj/set/operate method Enter the setting value and press OK key.
Caution Increase/decrease the value 1 by 1 and check the symptom each
time.
Display/adj/set range -10 to 10
Unit 5 uA
Default value 0
2TR-TGT3 Sec transfer current adj value (Ev 2)
Lv.2 Details To set the target current that is applied to the secondary transfer
inner roller under the condition of absolute moisture ratio from 1.73
to 5.79 g/m 3 .
When low-voltage mottled image or toner splash on solid image
occurs, increase the current.
When high-voltage mottled image or density loss due to excessive
transfer occurs, decrease the current.
As the value is changed by 1, current is increased/decreased by
5 uA.
+: Increase
-: Decrease
Use case When image failures occur on all the paper types (mottled image/
density loss due to excessive transfer/toner splash on solid image)
Adj/set/operate method Enter the setting value and press OK key.
Caution Increase/decrease the value 1 by 1 and check the symptom each
time.
Display/adj/set range -10 to 10
Unit 5 uA
Default value 0
8
Service Mode > COPIER > ADJUST (Adjustment Mode) > HV-TR
8 Service Mode > COPIER > ADJUST (Adjustment Mode) > HV-TR
COPIER> ADJUST> HV-TR
2TR-TGT4 Sec transfer current adj value (Ev 3)
Lv.2 Details To set the target current that is applied to the secondary transfer
inner roller under the condition of absolute moisture ratio from 5.8 to
3
8.89 g/m .
When low-voltage mottled image or toner splash on solid image
occurs, increase the current.
When high-voltage mottled image or density loss due to excessive
transfer occurs, decrease the current.
As the value is changed by 1, current is increased/decreased by
5 uA.
+: Increase
-: Decrease
Use case When image failures occur on all the paper types (mottled image/
density loss due to excessive transfer/toner splash on solid image)
Adj/set/operate method Enter the setting value and press OK key.
Caution Increase/decrease the value 1 by 1 and check the symptom each
time.
Display/adj/set range -10 to 10
Unit 5 uA
Default value 0
2TR-TGT5 Sec transfer current adj value (Ev 4)
Lv.2 Details To set the target current that is applied to the secondary transfer
inner roller under the condition of absolute moisture ratio from 8.9 to
14.9 g/m 3 .
When low-voltage mottled image or toner splash on solid image
occurs, increase the current.
When high-voltage mottled image or density loss due to excessive
transfer occurs, decrease the current.
As the value is changed by 1, current is increased/decreased by
5 uA.
+: Increase
-: Decrease
Use case When image failures occur on all the paper types (mottled image/
density loss due to excessive transfer/toner splash on solid image)
Adj/set/operate method Enter the setting value and press OK key.
Caution Increase/decrease the value 1 by 1 and check the symptom each
time.
Display/adj/set range -10 to 10
Unit 5 uA
Default value 0
8-185
8-185