Canon imagePRESS 1135 Series Service Manual page 1106

■ CCD
COPIER> ADJUST> CCD
W-PLT-X White level data(X) entry of white plate
Lv.1 Details When the reader controller PCB is replaced or RAM is cleared, enter
the value of service label and when the copyboard glass is replaced,
enter the value of barcode label that is affixed on the glass.
Use case When the reader controller PCB is replaced or RAM is cleared.
When the copyboard glass is replaced.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, enter the changed value in the
service label.
Display/adj/set range 7500 to 9999
Default value 8271
Related service mode COPIER> ADJUST> CCD> W-PLT-Y, W-PLT-Z, BW-TGT
W-PLT-Y White level data(Y) entry of white plate
Lv.1 Details When the reader controller PCB is replaced or RAM is cleared, enter
the value of service label and when the copyboard glass is replaced,
enter the value of barcode label that is affixed on the glass.
Use case When the radar controller PCB is replaced or RAM is cleared.
When the copyboard glass is replaced.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, enter the changed value in the
service label.
Display/adj/set range 7500 to 9999
Default value 8735
Related service mode COPIER> ADJUST> CCD> W-PLT-X, W-PLT-Z, BW-TGT
W-PLT-Z White level data(Z) entry of white plate
Lv.1 Details When the reader controller PCB is replaced or RAM is cleared, enter
the value of service label and when the copyboard glass is replaced,
enter the value of barcode label that is affixed on the glass.
Use case When the radar controller PCB is replaced or RAM is cleared.
When the copyboard glass is replaced.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, enter the changed value in the
service label.
Display/adj/set range 7500 to 9999
Default value 9418
Related service mode COPIER> ADJUST> CCD> W-PLT-X, W-PLT-Y, BW-TGT
8
Service Mode > COPIER > ADJUST (Adjustment Mode) > CCD
8 Service Mode > COPIER > ADJUST (Adjustment Mode) > CCD
COPIER> ADJUST> CCD
SH-TRGT Shading target value (B&W) [Copyboard]
Lv.1 Details To set the B&W shading target value in copyboard reading mode.
Use case When the reader controller PCB is replaced or RAM is cleared.
When the scanner unit is replaced.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, enter the changed value in the
service label.
Display/adj/set range 700 to 1400
Default value 1126
100-RG RG color drift crrctVL in img snsr[Frnt]
Lv.1 Details To correct the color drift between R-G lines in sub scanning direction
due to the front side scanner unit.
When the reader controller PCB is replaced or RAM is cleared, enter
the value of service label.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power.
Caution After the setting value is changed, enter the changed value in the
service label.
Display/adj/set range -256 to 256
Default value 0
100-GB GB color drift crrctVL in img snsr[Frnt]
Lv.1 Details To correct the color drift between G-B lines in sub scanning direction
due to the front side scanner unit.
When the reader controller PCB is replaced or RAM is cleared, enter
the value of service label.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power.
Caution After the setting value is changed, enter the changed value in the
service label.
Display/adj/set range -256 to 256
Default value 0
8-163
8-163