Canon imagePRESS 1135 Series Service Manual page 1232

COPIER > OPTION > USER
IFAX-SZL Setting of IFAX send size limit
Lv.2 Details Setting for restricting data size at the time of IFAX transmission that
does not go through the server.
With the setting to restrict the data size, there will be #830 error in
the case of sending data that exceeds the upper limit value.
In the case that the data goes through the server, the size of
transmission data is always restricted.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: Restriction, 1: No restriction (restriction applies when data goes
through the server)
Default value 1
Related user mode System Settings> Communication Settings> E-mail/ IFAX Common
Settings> Transmission Data Size Upper Limit Value
Supplement/memo Specify the upper limit value for transmission data size in User Mode.
IFAX-PGD Set page split TX at IFAX Simple mode TX
Lv.2 Details Setting to enable/disable split-data transmission on a page basis in
the case that the transmission size with IFAX Simple mode exceeds
the upper limit value.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution In the case to enable split-data transmission, be sure to explain the
following to the user to get an approval:
• No guarantee for page order at receiving side
• There is a possibility of interruption of other received job between
pages
Display/adj/set range 0 to 1
0: Disable this mode, 1: Enable this mode
Default value 0
Related user mode System Settings> Communication Settings> E-mail/IFAX Common
Settings> Upper limit value for transmission data size
Supplement/memo Specify the upper limit value for transmission data size in User Mode.
8
Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > USER
8 Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > USER
COPIER > OPTION > USER
MEAPSAFE Setting of MEAP safe mode
Lv.2 Details Setting of safe mode for MEAP platform.
MPSF is displayed on the control panel in safe mode.
In safe mode, MEAP application is stopped while just the system
application, which starts with initial state, is activated. This mode
enables obtaining log for cause analysis of MEAP failure.
Use case To perform system recovery processing in the case that MEAP
platform fails to be activated due to resource competition between
MEAP applications, service registration or use order.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: Normal mode, 1: Safe mode
Default value 0
AFN-PSWD Access limit setting to user mode
Lv.2 Details Setting to restrict password entry when accessing to User Mode.
With this setting enabled, password entry of system administrator is
required after pressing Additional Functions button.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: Password is not required, 1: Password is required
Default value 0
PTJAM-RC Auto reprint setting at PDL print jam
Lv.2 Details Setting to automatically start printing after jam recovery that occurs
with PDL print.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: No automatic reprint, 1: Automatic reprint
Default value 1
PDL-NCSW Card managemnt setting for PDL print job
Lv.2 Details Setting to make PDL print job to be subject to card management by
the card reader.
With the setting to enable this mode, PDL print is available only
when the card ID of the card inserted to the card reader matches the
department ID.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: PDL print is available with no card inserted.
1: PDL print is available only when the card ID matches the
department ID when the card is inserted.
Default value 0
8-289
8-289