Canon imagePRESS 1135 Series Service Manual page 1147

COPIER> ADJUST> FEED-ADJ
REGCST10 Storage side regst adj dspl:Pikup deck10
Lv.1 Details Display the side registration misalignment position amount of the
storage of the second secondary POD lower deck.
As an indicator when side registration the storage is adjusted.
Use case When adjusting the side registration of the storage in case that the
correction is not enough at the active registration.
Adj/set/operate method 1) Report the side registration correction amount of each pickup
cassette at the last feed.
2) Display the 1) value on the control panel (rear: +, front: -, unit:
mm)
3) Adjust the side registration position of pickup cassette according
to the displayed value.
If the value is within the adjustment range of active registration (-1
to 1 mm), adjustment is not necessary.
Caution • After the side registration adjustment of storage, feed the paper
and check the result.
• Do not move the storage that is adjusted for transparency other
than user's request.
Display/adjust/set range -10 to 10
Unit 1 mm
Appropriate target value -6 to 6
Default value 0
Supplement/memo On [side registration shift amount offset] that is the fixing assembly
paper edge measure, the value is displayed regardless of the side
registration correction amount.
TS-TEMP Temp-related lead edge margin change adj
Lv.2 Details To adjust the changes of leading edge margin caused by the
temperature.
Image writing start position is adjusted based on the detected
temperature of ITB environment sensor (PS124); however, leading
edge margin may increase/decrease at continuous feed.
If the margin after feed becomes larger than the one at job start,
enter the negative value and if it becomes smaller, enter the positive
value.
As the value is changed by 1, changes of margin is increased/
decreased by 0.3 mm.
Use case When the leading edge margin changes at continuous feed.
Adj/set/operate method 1) Ask users to prepare several sheets of output paper at job start
and after the continuous feed (approx. 5 sheets each).
2) Measure the leading edge margin of each output paper and
calculate the difference from the average value.
Changes of margin = margin at jog start - margin after continuous
feed
3) Enter the setting value and press OK key.
Display/adjust/set range -50 to 50
Unit 0.3 mm
Default value 0
8
Service Mode > COPIER > ADJUST (Adjustment Mode) > FEED-ADJ
8 Service Mode > COPIER > ADJUST (Adjustment Mode) > FEED-ADJ
COPIER> ADJUST> FEED-ADJ
DUPDCL01 Dplx decrlr inlet mrgn adj (pikup deck1)
Lv.1 Details Use the paper on the host machine deck as a target, adjust the
pressure level of the duplex decurler roller.
If the pressure level of the duplex decurler roller is increased, the
paper that pass the duplex path will have upper curl after both sides
repick up. If it becomes upper curl, failure image (specially thick
paper trailing edge density step) can be reduced.
The bigger the value is, the pressure level is increased.
Increase the level one by one while checking the improvement of the
image.
Use case When image failure (specially thick paper trailing edge density step)
occurs
Adj/set/operate method Input the setting value, and press OK.
Caution Jam might occur in a paper with feeding direction less than 240 mm
(jam code; 0112).
Display/adjust/set range 0 to 10
Appropriate target value 0
Default value 0
DUPDCL02 Dplx decrlr inlet mrgn adj (pikup deck2)
Lv.1 Details Use the paper on the POD upper deck as a target, adjust the
pressure level of the duplex decurler roller.
If the pressure level of the duplex decurler roller is increased, the
paper that pass the duplex path will have upper curl after both sides
repick up. If it becomes upper curl, failure image (specially thick
paper trailing edge density step) can be reduced.
The bigger the value is, the pressure level is increased.
Increase the level one by one while checking the improvement of the
image.
Use case When image failure (specially thick paper trailing edge density step)
occurs
Adj/set/operate method Input the setting value, and press OK.
Caution Jam might occur in a paper with feeding direction less than 240 mm
(jam code; 0112).
Display/adjust/set range 0 to 10
Appropriate target value 0
Default value 0
8-204
8-204