Canon imagePRESS 1135 Series Service Manual page 1179

COPIER > OPTION > FNC-SW
CE/SCNR Dspl times of scanner connectr disconnct
Lv.1 Details Setting to display/change the number of detection for disconnection
of the scanner's connector.
To be counted every time disconnection of the connector is detected.
Selecting 0 can reset the counter (number of detection).
Use case To check/clear the number of detection for disconnecting of the
connector.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 5
Default value 0
Supplement/memo "Check the connector" is displayed on the control panel when the
connector is disconnected.
E code (E732-000) is displayed once the number of detection
reaches the specified value.
INTROT-3 Interval set of post-rotation control 3
Lv.1 Details Set the number of sheets between intervals for D-half control (quick
automatic gradation correction) at the time of last rotation.
When the value is incremented by 1, the number of sheets between
intervals is increased by 500 sheets. When 0 is specified, the control
is not executed.
Use case To match the use environment of the user.
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Increase the number of sheets (increase the interval) causes higher
frequency of image fault.
Display/adj/set range 0 to 255
0: No control
Unit 500 sheets
Default value 0
INTROT-4 Interval set of post-rotation control 4
Lv.1 Details Set the number of sheets between intervals for black band
(discharging) which operates only for low duty at the time of last
rotation.
When the value is incremented by 1, the number of sheets between
intervals is increased by 100 sheets. When 0 is specified, the control
is not executed.
Use case To match the use environment of the user.
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Increase the number of sheets (increase the interval) causes higher
frequency of image fault.
Display/adj/set range 0 to 255
0: No control
Unit 100 sheets
Default value 0
8
Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > FNC-SW
8 Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > FNC-SW
COPIER > OPTION > FNC-SW
INTER-1 Bk band ctrl intervl set: low Duty only
Lv.1 Details Set the number of sheets between intervals for black band
(discharging) control which operates only for low duty.
When the value is incremented by 1, the number of sheets between
interruption intervals is increased by 100 sheets. When 0 is specified,
the control is not executed.
Use case To match the use environment of the user.
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Increase the number of sheets (increase the interval) causes higher
frequency of image fault.
Display/adj/set range 0 to 255
0: No control
Unit 100 sheets
Default value 15
INTER-2 Potential/simple D-max ctrl interval set
Lv.1 Details Set the number of sheets between intervals for potential control and
simple D-max control.
When the value is incremented by 1, the number of sheets between
interruption intervals is increased by 100 sheets. When 0 is specified,
the control is not executed.
Use case To match the use environment of the user.
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Increase the number of sheets (increase the interval) causes higher
frequency of image fault.
Display/adj/set range 0 to 255
0: No control
Unit 100 sheets
Default value 80
INTER-3 Set sheet interval at interrupt cntrl3
Lv.1 Details Set the number of sheets between intervals for Interrupt Control 3
(secondary transfer cleaning control).
When the value is incremented by 1, the number of sheets between
intervals for interrupt is increased by 50 sheets. When the value is
set to 0, no control is executed.
Use case To suit the use environment of the user
Adj/set/operate method Enter the setting value and press the OK key.
Caution When the number of sheets is increased (when the interval is
increased), the image failure occurrence ratio is increased. When dirt
occurred to the backside or edge of the paper, decrease the number
of sheets.
Display/adj/set range 0 to 255
0: No control is executed.
Unit 50 sheets
Default value 15
8-236
8-236