Canon imagePRESS 1135 Series Service Manual page 1171

■ SENS-ADJ
COPIER> FUNCTION> SENS-ADJ
OP-SENS Auto adjustment of scanner sensor
Lv.2 Details Automatically adjust the following optical sensors.
Image standard sensor for OHP (PS41), Image standard sensor
(PS42), First skew sensor (front/rear) (PS47/PS48), Second skew
sensor (front/rear) (PS49/PS50), First skew sensor for OHP (front/
rear) (PS51/PS52), Second skew sensor for OHP (front/rear) (PS53/
PS54), Post-registration sensor (PS59), Post-registration sensor for
OHP (PS60)
The result is displayed starting from the sensor for which adjustment
was completed.
Clean/replace the sensor for which NG was displayed.
Use case At the time of replacement of each sensor
Adj/set/operate method 1) Set paper in all pickup inlets.
2) Select the item and press the OK key.
Caution If NG was displayed, execute OP-SENS again after cleaning the
surface of the sensor.
If NG was again displayed, replace the sensor.
Display/adjust/set range Upper 2 digits: During operation: ACTIVE, When operation finished
normally: OK, When operation failed: NG
Lower 36 digits: Result at termination
Required time Approx. 5 minutes
CIS Adjustment of CIS light intensity
Lv.1 Details Automatically adjust the current value to determine the LED light
intensity of the CIS.
Use case At the time of replacement of the CIS
Adj/set/operate method Select the item and press the OK key.
Display/adjust/set range During operation: ACTIVE, When operation finished normally: OK,
When operation failed: NG
Default value 0
Required time Approx. 45 seconds
Supplement/memo The CIS exists in the paper feed assembly.
8
Service Mode > COPIER > FUNCTION (Operation / Inspection Mode) > SYSTEM
T-8-58
8 Service Mode > COPIER > FUNCTION (Operation / Inspection Mode) > SYSTEM
■ SYSTEM
COPIER> FUNCTION> SYSTEM
DOWNLOAD Shift to download mode
Lv.1 Details Make the machine enter the download mode and wait for a
command.
Perform downloading by SST.
Use case At the time of version update
Adj/set/operate method 1) Select the item and press the OK key.
2) Perform downloading by SST.
Caution Do not turn off the power before HOLD is displayed.
Display/adjust/set range When waiting for a command: STAND-BY/STNDBY, In
communication: CONNECTED, Communication terminated: HOLD
Supplement/memo SST: Service Support Tool
CHK-TYPE Specifing HD-CLEAR/HD-CHECK partition
Lv.1 Details Specify the partition number of the HDD to execute HD-CLEAR/HD-
CHECK.
Use case At the time of execution of HD-CLEAR/HD-CHECK
Adj/set/operate method Enter the value and press the OK key.
Display/adjust/set range 0 to 65535
0: Entire HDD
1: Image accumulation area
2: Universal file storage area
3: PDL file storage area
4: Program file storage area
5: MEAP application
6: Address book transfer setting
7: MEAP storage data
8: System log storage area
Related service mode COPIER> FUNCTION> SYSTEM> HD-CLEAR, HD-CHECK
Supplement/memo Universal file: Management information of user setting data, various
log data, PDL spool data, and image data, etc.
HD-CHECK Entire HDD check and retrieval
Lv.1 Details Check the entire HDD and execute recovery processing.
Adj/set/operate method Select the item and press the OK key.
Caution Be sure to execute this item after CHK-TYPE.
Display/adjust/set range 0 to 4
0: Check the sector of the entire HDD and perform recovery
1: Image accumulation area
2: Universal file storage area
3: PDL file storage area
4. Program file storage area
Related service mode COPIER> FUNCTION> SYSTEM> CHK-TYPE
Supplement/memo Universal file: Management information of user setting data, various
log data, PDL spool data, and image data, etc.
8-228
8-228