Canon imagePRESS 1135 Series Service Manual page 1383

SORTER> ADJUST
TRM-RG1 Skew adj (small size): Fin-AG
Lv.1 Details On the trimmer of the finisher, to adjust the skew on the stack of A4
size or smaller.
As the value is changed by 1, the paper stack stop position moves
by 0.1 mm.
+: toward delivery side
-: toward inlet side
Use case When the skew occurs on the paper stack of A4 or smaller
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power.
Display/adj/set range -50 to 50
Unit 0.1 mm
Appropriate target value 0
TRM-RG2 Skew adj (large size): Fin-AG
Lv.1 Details On the trimmer of the finisher, to adjust the skew on the stack that is
larger than A4.
As the value is changed by 1, the paper stack stop position moves
by 0.1 mm.
+: toward delivery side
-: toward inlet side
Use case When the skew occurs on the paper stack that is larger than A4
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power.
Display/adj/set range -50 to 50
Unit 0.1 mm
Appropriate target value 0
TRM-CUT1 Trimming position adj (S size): Fin-AG
Lv.1 Details On the trimmer of the finisher, to adjust the trimming position on the
stack of A4 size or smaller.
As the value is changed by 1, the paper stack stop position moves
by 0.1 mm.
+: toward delivery side
-: toward inlet side
Use case When the trimming position is displaced on the paper stack of A4 or
smaller
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power.
Display/adj/set range -50 to 50
Unit 0.1 mm
Appropriate target value 0
8
Service Mode > SORTER > ADJUST
8 Service Mode > SORTER > ADJUST
SORTER> ADJUST
TRM-CUT2 Trimming position adj (L size): Fin-AG
Lv.1 Details On the trimmer of the finisher, to adjust the trimming position on the
stack that is larger than A4.
As the value is changed by 1, the paper stack stop position moves
by 0.1 mm.
+: toward delivery side
-: toward inlet side
Use case When the trimming position is displaced on the paper stack that is
larger than A4
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power.
Display/adj/set range -50 to 50
Unit 0.1 mm
Appropriate target value 0
ST2-PULL Lead-in belt up/down motr pstn adj: stk2
Lv.1 Details To adjust the position of up/down motor of lead-in belt at the feed
direction side on the stack unit on the secondary stacker.
As the value is increased, lead-in force is reduced.
Use case Restore the position to the factory setting when EEPROM/master
controller PCB is replaced.
Adj/set/operate method Enter the setting value and press OK key.
Display/adj/set range 0 to 4
Default value 0
BFF-SFT2 Paper displace amount on buffer: Fin-AG
Lv.1 Details To adjust the paper displacement amount on Finisher Buffer
Assembly.
As the value is incremented by 1, the paper position moves by
0.1 mm.
+:
-:
Use case When the paper displacement occurs on the 2nd to 3rd sheets of the
2nd sets (B5/A4/LTR) and later
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value 0
8-440
8-440