Canon imagePRESS 1135 Series Service Manual page 1375

SORTER> ADJUST
GLUAMT2C Coated paper glue amount adj2: trimmer
Lv.1 Details To adjust the glue application amount on the coated paper on the
return way at the glue thick application by changing the space
between the paper stack (thickness 1.5 to 3.4 mm) and the scraper
plate.
As the value is changed by 1, the space gets wider/narrower by
0.05 mm (as the space is widened, the glue application amount is
increased).
+: space is widened (application amount increased)
-: space is narrowed (application amount is decreased)
Use case When glue peeling occurs with normal glue application amount on
the coated inner sheet
Display/adj/set range -20 to 20
Unit 0.05 mm
Default value 0
GLUAMT3C Coated paper glue amount adj3: trimmer
Lv.1 Details To adjust the glue application amount on the coated paper on the
return way at the glue thick application by changing the space
between the paper stack (thickness 3.5 to 6.4 mm) and the scraper
plate.
As the value is changed by 1, the space gets wider/narrower by
0.05 mm (as the space is widened, the glue application amount is
increased).
+: space is widened (application amount increased)
-: space is narrowed (application amount is decreased)
Use case When glue peeling occurs with normal glue application amount on
the coated inner sheet
Display/adj/set range -20 to 20
Unit 0.05 mm
Default value 0
GLUAMT4C Coated paper glue amount adj4: trimmer
Lv.1 Details To adjust the glue application amount on the coated paper on the
return way at the glue thick application by changing the space
between the paper stack (thickness 6.5 to 11.4 mm) and the scraper
plate.
As the value is changed by 1, the space gets wider/narrower by
0.05 mm (as the space is widened, the glue application amount is
increased).
+: space is widened (application amount increased)
-: space is narrowed (application amount is decreased)
Use case When glue peeling occurs with normal glue application amount on
the coated inner sheet
Display/adj/set range -20 to 20
Unit 0.05 mm
Default value 0
8
Service Mode > SORTER > ADJUST
8 Service Mode > SORTER > ADJUST
SORTER> ADJUST
GLUAMT5C Coated paper glue amount adj5: trimmer
Lv.1 Details To adjust the glue application amount on the coated paper on the
return way at the glue thick application by changing the space
between the paper stack (thickness 11.5 to 22.4 mm) and the
scraper plate.
As the value is changed by 1, the space gets wider/narrower by
0.05 mm (as the space is widened, the glue application amount is
increased).
+: space is widened (application amount increased)
-: space is narrowed (application amount is decreased)
Use case When glue peeling occurs with normal glue application amount on
the coated inner sheet
Display/adj/set range -20 to 20
Unit 0.05 mm
Default value 0
GLUAMT6C Coated paper glue amount adj6: trimmer
Lv.1 Details To adjust the glue application amount on the coated paper on the
return way at the glue thick application by changing the space
between the paper stack (thickness 22.5 to 25 mm) and the scraper
plate.
As the value is changed by 1, the space gets wider/narrower by
0.05 mm (as the space is widened, the glue application amount is
increased).
+: space is widened (application amount increased)
-: space is narrowed (application amount is decreased)
Use case When glue peeling occurs with normal glue application amount on
the coated inner sheet
Display/adj/set range -20 to 20
Unit 0.05 mm
Default value 0
ST1-ALR1 Stckr right tray rear align plate: stk
Lv.1 Details To adjust the position of rear alignment plate of the right tray on the
stack unit of the stacker.
As the value is increased by 1, the rear alignment plate moves by
0.16 mm.
+: toward front (narrow)
-: toward rear (widen)
Use case Restore the position to the factory setting when EEPROM/master
controller PCB is replaced
Adj/set/operate method Enter the setting value and press OK key.
Display/adj/set range -32 to 32
Unit 0.16 mm
Default value 0
8-432
8-432