Canon imagePRESS 1135 Series Service Manual page 1382

SORTER> ADJUST
PRCS-ALG Process tray align plate width: Fin-AG
Lv.1 Details To adjust the width of the alignment plate on the process tray
assembly on the finisher.
As the value is changed by 1, the width of alignment plate is
increased/decreased by 0.1 mm.
+: increase (widen)
-: decrease (narrow)
Use case When the paper displacement occurs on paper stack
Adj/set/operate method Enter the setting value and press OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
STP-F1 Front 1-staple position(R size): Fin-AG
Lv.1 Details To adjust the position of front 1-staple on the finisher for A4R/LGL/
LTRR paper.
As the value is changed by 1, the staple position moves by 0.1 mm.
+: toward front
-: toward rear
Use case When the front staple position is displaced on the A4R/LGL/LTRR
paper
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power.
Display/adj/set range -50 to 50
Unit 0.1 mm
STP-F2 Front 1-staple positn(half size): Fin-AG
Lv.1 Details To adjust the position of front 1-staple on the finisher for A3/B4/A4/
B5/LDR/LTR/EXEC/8K/16K paper.
As the value is changed by 1, the staple position moves by 0.1 mm.
+: toward front
-: toward rear
Use case When the front staple position is displaced on the A3/B4/A4/B5/LDR/
LTR/EXEC/8K/16K paper
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power.
Display/adj/set range -50 to 50
Unit 0.1 mm
STP-R1 Rear 1-staple position(R size): Fin-AG
Lv.1 Details To adjust the position of rear 1-staple on the finisher for A4R/LGL/
LTRR paper.
As the value is changed by 1, the staple position moves by 0.1 mm.
+: toward front
-: toward rear
Use case When the rear staple position is displaced on the A4R/LGL/LTRR
paper
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power.
Display/adj/set range -50 to 50
Unit 0.1 mm
8
Service Mode > SORTER > ADJUST
8 Service Mode > SORTER > ADJUST
SORTER> ADJUST
STP-R2 Rear 1-staple positin(half size): Fin-AG
Lv.1 Details To adjust the position of rear 1-staple on the finisher for A3/B4/A4/
B5/LDR/LTR/EXEC/8K/16K paper.
As the value is changed by 1, the staple position moves by 0.1 mm.
+: toward front
-: toward rear
Use case When the rear staple position is displaced on the A3/B4/A4/B5/LDR/
LTR/EXEC/8K/16K paper
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power.
Display/adj/set range -50 to 50
Unit 0.1 mm
STP-2P 2-staple front/rear position: Fin-AG
Lv.1 Details To adjust the front/rear position of 2-staple on the finisher.
As the value is changed by 1, the staple position moves by 0.1 mm.
+: toward front
-: toward rear
Use case When the front/rear position of 2-staple is displaced
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power.
Display/adj/set range -50 to 50
Unit 0.1 mm
BFF-SFT Paper displace amount on buffer: Fin-AG
Lv.1 Details Adjust the paper dislocation amount of buffer assembly of the finisher
Increase the input value by 1, the paper location will move by 0.1 mm.
+:
-:
Use case On the 2nd stack of B5/A4/LTR or later, if paper displacement occurs
at 1st to 3rd paper within the paper stack
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power.
Display/adj/set range -50 to 50
Unit 0.1 mm
PNCH-X Punch hole position in feed way: Fin-AG
Lv.1 Details To adjust the position of punch hole of finisher in feed direction.
As the value is changed by 1, punch hole moves by 0.1 mm.
+: toward delivery side
-: toward inlet side
Use case When punch hole is displaced in feed direction
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power.
Display/adj/set range -20 to 20
Unit 0.1 mm
Appropriate target value 0
8-439
8-439