Canon imagePRESS 1135 Series Service Manual page 1137

COPIER> ADJUST> HV-TR
1TR-TGT3 Adj of prmry trnsfer target current(Ev2)
Lv.2 Details To set the target current that is applied to the primary transfer roller
under the condition of absolute moisture ratio from 1.73 to 5.79 g/m
When mottled image occurs, increase the current and when water-
drop mark occurs, decrease the current.
As the value is increased by 1, the current is increased by 5 uA.
+: Increase
-: Decrease
Use case When the image failure due to primary transfer occurs (related to
mottled image, water-drop mark)
Adj/set/operate method Enter the setting value and press OK key.
Caution Increase/decrease the value 1 by 1 and check the symptom each
time. If too large value is set, high-voltage mottled image occurs.
Display/adj/set range -10 to 10
Unit 5 uA
Default value 0
1TR-TGT4 Adj of prmry trnsfer target current(Ev3)
Lv.2 Details To set the target current that is applied to the primary transfer roller
under the condition of absolute moisture ratio from 5.8 to 8.89 g/m
When mottled image occurs, increase the current and when water-
drop mark occurs, decrease the current.
As the value is increased by 1, the current is increased by 5 uA.
+: Increase
-: Decrease
Use case When the image failure due to primary transfer occurs (related to
mottled image, water-drop mark)
Adj/set/operate method Enter the setting value and press OK key.
Caution Increase/decrease the value 1 by 1 and check the symptom each
time. If too large value is set, high-voltage mottled image occurs.
Display/adj/set range -10 to 10
Unit 5 uA
Default value 0
8
Service Mode > COPIER > ADJUST (Adjustment Mode) > HV-TR
3
.
3
.
8 Service Mode > COPIER > ADJUST (Adjustment Mode) > HV-TR
COPIER> ADJUST> HV-TR
1TR-TGT5 Adj of prmry trnsfer target current(Ev4)
Lv.2 Details To set the target current that is applied to the primary transfer roller
under the condition of absolute moisture ratio from 8.9 to 14.9 g/m
When mottled image occurs, increase the current and when water-
drop mark occurs, decrease the current.
As the value is increased by 1, the current is increased by 5 uA.
+: Increase
-: Decrease
Use case When the image failure due to primary transfer occurs (related to
mottled image, water-drop mark)
Adj/set/operate method Enter the setting value and press OK key.
Caution Increase/decrease the value 1 by 1 and check the symptom each
time. If too large value is set, high-voltage mottled image occurs.
Display/adj/set range -10 to 10
Unit 5 uA
Default value 0
Related service mode COPIER> ADJUST> HV-TR> 1TR-TGT1, 1TR-TGT2, 1TR-TGT3,
1TR-TGT4, 1TR-TGT6, 1TR-TGT7, 1TR-TGT8
1TR-TGT6 Adj of prmry trnsfer target current(Ev5)
Lv.2 Details To set the target current that is applied to the primary transfer roller
under the condition of absolute moisture ratio from 15 to 17.9 g/m
When mottled image occurs, increase the current and when water-
drop mark occurs, decrease the current.
As the value is increased by 1, the current is increased by 5 uA.
+: Increase
-: Decrease
Use case When the image failure due to primary transfer occurs (related to
mottled image, water-drop mark)
Adj/set/operate method Enter the setting value and press OK key.
Caution Increase/decrease the value 1 by 1 and check the symptom each
time. If too large value is set, high-voltage mottled image occurs.
Display/adj/set range -10 to 10
Unit 5 uA
Default value 0
Related service mode COPIER> ADJUST> HV-TR> 1TR-TGT1, 1TR-TGT2, 1TR-TGT3,
1TR-TGT4, 1TR-TGT5, 1TR-TGT7, 1TR-TGT8
8-194
3
.
3 .
8-194