Canon imagePRESS 1135 Series Service Manual page 1267

COPIER> TEST> PG
DENS-K Adj of Bk color density at test print
Lv.1 Details To adjust Bk color density when performing test print (TYPE=5).
As the greater value is set, the image gets darker.
Use case At test print (TYPE=5)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 25
Default value -
F/M-SW Set of PG full color/mono color
Lv.1 Details Setting for output in full color/monochrome color with PG
Use case To separate (identify) the cause whether it's due to color or
monochrome
Adj/set/operate method Select the item, and then press OK key.
Display/adjust/set range 0 to 1
0: Full color, 1: Monochrome color
PG-PICK Set of test print pickup cassette
Lv.1 Details Setting of pickup cassette for test print output
Use case At the time of trouble analysis with test print output
Adj/set/operate method Select the item, and then press OK key.
Display/adjust/set range 1 to 19
1: Host machine deck
2 to 7: Not used
8: POD upper deck, 9: POD middle deck, 10: POD lower deck
11: Secondary POD upper deck, 12: Secondary POD middle deck,
13: Secondary POD lower deck
14: (2nd) Secondary POD 2 upper deck,
15: (2nd) Secondary POD 2 middle deck,
16: (2nd) Secondary POD 2 lower deck
17: Multiple deck upper deck,
18: Multiple deck middle deck,
19: Multiple deck lower deck
2-SIDE Set of PG 2-sided mode
Lv.1 Details Setting of 1-sided/2-sided print for PG output
Use case At the time of trouble analysis
Adj/set/operate method Select the item, and then press OK key.
Display/adjust/set range 0 to 1
0: 1-sided, 1: 2-sided
Default value 0
PG-QTY Setting number of PG output
Lv.1 Details Setting the number of sheets for PG output
Use case At the time of trouble analysis
Display/adjust/set range 1 to 999
Unit 1 sheet
Default value 1
8
Service Mode > COPIER > TEST (Test Print Mode) > PG
8 Service Mode > COPIER > TEST (Test Print Mode) > PG
COPIER> TEST> PG
FINISH Accessory processing function test print
Lv.1 Details Executing test print relating to accessory processing function
Use case When checking operation of accessory processing function
Adj/set/operate method 1) Enter the number of sheets with PG-QTY, and then press OK key.
2) Enter the setting value, and then press OK key.
3) Press Start button.
The machine outputs test print.
Display/adjust/set range 0 to 99
0: N.A.
1: Staple (front) *1
2: Staple (2-point) *1
3: Staple (rear) *1
4: Booklet (saddle stitch) *1
5: Z-fold (single sleeve) *1
6: 2-fold *1
7: C-fold *2
8: V-fold *2
9: 4-fold *2
10: Z-fold (outside 3-fold) *2
11: Punch (inner puncher) *3
12: Multiple-hole punch *4
13: Shift *1
14: 1-edge (booklet) trim *5
15: 3-edge trim *6
16 to 99: Spare (for future use)
*1 Finisher, *2 Multi-folding machine, *3 Inner puncher,
*4 Multiple puncher, *5 Booklet trimmer, *6 Booklet/two-knife trimmer
Default value 0
Related service mode COPIER> TEST> PG> PG-QTY
8-324
T-8-80
8-324