Canon imagePRESS 1135 Series Service Manual page 1070

Address bit Name
P078 15 -
14 -
13 -
12 -
11 -
10 Master download enable
9 RxD for writing data in the flash memory
(SST)
8 TxD for writing data in the flash memory
(SST)
7 Simulator communication (RDP) TxD
6 Simulator communication (RDP) RxD
5 EEPROM CS
4 EEPROM CLK
3 -
2 EERPM DO
1 GA CS
0 IPC CS
P079 15 -
14 EEPROM DI
13 Signal line output for slave CPU control
12 -
11 DAC_LD
10 DAC_CLK
9 DAC_DI
8 LED on PCB
7 Signature path 2 sensor
6 Signature path 1 sensor
5 Cover path 2 sensor
4 Cover path 1 sensor
3 Alignment home position sensor (rear/
large)
2 Alignment home position sensor (front/
large)
1 Alignment home positionsensor(rear/small) S13
0 Alignment home positionsensor(front/small) S12
8
Service Mode > COPIER > I / O > Perfect Binder (SORTER > P076 to P134)
Symbol Remarks
- -
- -
- -
- -
- -
- 0: Write enable
- -
- -
- -
- -
- 1: Select
- -
- -
- -
- 0: Select
- 0: Select
- -
- -
- -
- -
- -
- -
- -
- -
S19 1: Paper
S18 1: Paper
S26 1: Paper
S20 1: Paper
S15 1: Home position
S14 1: Home position
1: Home position
1: Home position
8 Service Mode > COPIER > I / O > Perfect Binder (SORTER > P076 to P134)
Address bit Name
P080 15 Insertion communication control - delivery
start request
14 Insertion communication control - device
configuration settings
13 Insertion communication control - Stacker
pre-joint sensor
12 Insertion communication control - serial
communication error
11 Alignment motor (front) PB / Stacking tray
shift motor PB
10 Alignment motor (front) PA / Stacking tray
shift motor PA
9 Alignment motor (front) EB / Stacking tray
shift motor EB
8 Alignment motor (front) EA / Stacking tray
shift motor EB
7 Switch-back flapper motor PB
6 Switch-back flapper motor PA
5 Switch-back flapper motor EB
4 Switch-back flapper motor EA
3 Switch-back roller lift motor B*-phase
2 Switch-back roller lift motor A*-phase
1 Switch-back roller lift motor B-phase
0 Switch-back roller lift motor A-phase
P081 15 Cover motor (R,L) enable
14 Cover motor (right) direction
13 Cover motor (left) direction
12 Cover motor (R,L) phase switch
11 Alignment motor (rear) PB / Stack weight
shift motor PB
10 Alignment motor (rear) PA / Stack weight
shift motor PA
9 Alignment motor (rear) EB / Stack weight
shift motor EB
8 Alignment motor (rear) EA / Stack weight
shift motor EA
7 -
6 -
5 -
4 -
3 Cover registration sensor
2 Switch-back roller upper/lower home
position sensor
1 Switch-back flapper home position sensor S10
0 Not use
8-127
Symbol Remarks
- -
- -
- 0: Paper
- 0: Error
M4, M9 -
M4, M9 -
M4, M9 -
M4, M9 -
M8 -
M8 -
M8 -
M8 --
M7 -
M7 -
M7 -
M7 -
M12, M13 1: Enable
M12 0: Feeding direction
M13 0: Feeding direction
M12, M13 0: 1-2phese, 1: W1-
2phese
M5, M6 -
M5, M6 -
M5, M6 -
M5, M6 -
- -
- -
- -
- -
S21 1: Paper
S11 1: Upper position
1: Upper position
- -
8-127