Canon imagePRESS 1135 Series Service Manual page 1135

COPIER> ADJUST> HV-TR
TR-DUP1 Set PPside for PPallotted volt adj: set1
Lv.2 Details To set the paper side for setting 1.
Setting 1 is the condition combination of environment, paper type
(paper weight) and feeding side that are set at TR-ENV1, TR-PPR1,
TR-DUP1. When this condition is true, paper allotted voltage that is
set at 2TR-TGT1 is applied to the secondary transfer inner roller.
Use case When an image failure that differs on 1st and 2nd side occurs (mottled
image/density loss due to excessive transfer/toner splash on solid
image).
Adj/set/operate method Enter the setting value and press OK key.
Display/adj/set range 1 to 4
1: Host 1st side, 2: Host 2nd side, 3: Deck 1st site, 4: Deck 2nd side
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-ENV1, TR-PPR1, 2TR-TGT1
TR-DUP2 Set PPside for PPallotted volt adj: set2
Lv.2 Details To set the paper side for setting 2.
Setting 2 is the condition combination of environment, paper type
(paper weight) and feeding side that are set at TR-ENV2, TR-PPR2,
TR-DUP2. When this condition is true, paper allotted voltage that is
set at 2TR-TGT2 is applied to the secondary transfer inner roller.
Use case When an image failure that differs on 1st and 2nd side occurs (mottled
image/density loss due to excessive transfer/toner splash on solid
image).
Adj/set/operate method Enter the setting value and press OK key.
Display/adj/set range 1 to 4
1: Host 1st side, 2: Host 2nd side, 3: Deck 1st site, 4: Deck 2nd side
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-ENV2, TR-PPR2, 2TR-TGT2
TR-DUP3 Set PPside for PPallotted volt adj: set3
Lv.2 Details To set the paper side for setting 3.
Setting 3 is the condition combination of environment, paper type
(paper weight) and feeding side that are set at TR-ENV3, TR-PPR3,
TR-DUP3. When this condition is true, paper allotted voltage that is
set at 2TR-TGT3 is applied to the secondary transfer inner roller.
Use case When an image failure that differs on 1st and 2nd side occurs (mottled
image/density loss due to excessive transfer/toner splash on solid
image).
Adj/set/operate method Enter the setting value and press OK key.
Display/adj/set range 1 to 4
1: Host 1st side, 2: Host 2nd side, 3: Deck 1st site, 4: Deck 2nd side
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-ENV3, TR-PPR3, 2TR-TGT3
8
Service Mode > COPIER > ADJUST (Adjustment Mode) > HV-TR
8 Service Mode > COPIER > ADJUST (Adjustment Mode) > HV-TR
COPIER> ADJUST> HV-TR
TR-DUP4 Set PPside for PPallotted volt adj: set4
Lv.2 Details To set the paper side for setting 4.
Setting 4 is the condition combination of environment, paper type
(paper weight) and feeding side that are set at TR-ENV4, TR-PPR4,
TR-DUP4. When this condition is true, paper allotted voltage that is
set at 2TR-TGT4 is applied to the secondary transfer inner roller.
Use case When an image failure that differs on 1st and 2nd side occurs (mottled
image/density loss due to excessive transfer/toner splash on solid
image).
Adj/set/operate method Enter the setting value and press OK key.
Display/adj/set range 1 to 4
1: Host 1st side, 2: Host 2nd side, 3: Deck 1st site, 4: Deck 2nd side
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-ENV4, TR-PPR4, 2TR-TGT4
TR-DUP5 Set PPside for PPallotted volt adj: set5
Lv.2 Details To set the paper side for setting 5.
Setting 5 is the condition combination of environment, paper type
(paper weight) and feeding side that are set at TR-ENV5, TR-PPR5,
TR-DUP5. When this condition is true, paper allotted voltage that is
set at 2TR-TGT5 is applied to the secondary transfer inner roller.
Use case When an image failure that differs on 1st and 2nd side occurs (mottled
image/density loss due to excessive transfer/toner splash on solid
image).
Adj/set/operate method Enter the setting value and press OK key.
Display/adj/set range 1 to 4
1: Host 1st side, 2: Host 2nd side, 3: Deck 1st site, 4: Deck 2nd side
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-ENV5, TR-PPR5, 2TR-TGT5
TR-DUP6 Set PPside for PPallotted volt adj: set6
Lv.2 Details To set the paper side for setting 6.
Setting 6 is the condition combination of environment, paper type
(paper weight) and feeding side that are set at TR-ENV6, TR-PPR6,
TR-DUP6. When this condition is true, paper allotted voltage that is
set at 2TR-TGT6 is applied to the secondary transfer inner roller.
Use case When an image failure that differs on 1st and 2nd side occurs (mottled
image/density loss due to excessive transfer/toner splash on solid
image).
Adj/set/operate method Enter the setting value and press OK key.
Display/adj/set range 1 to 4
1: Host 1st side, 2: Host 2nd side, 3: Deck 1st site, 4: Deck 2nd side
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-ENV6, TR-PPR6, 2TR-TGT6
8-192
8-192