Canon imagePRESS 1135 Series Service Manual page 1113

COPIER> ADJUST> CCD
DFCH-G10 Complex chart No.10 data (G) [Back]
Lv.1 Details To calculate the front/back linearity, set the back Green data of No.10
image in DADF complex chart.
Enter the value of reader's service label.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2550
Default value 0
Related service mode COPIER> ADJUST> CCD> DFCH-R2, DFCH-R10, DFCH-B2,
DFCH-B10, DFCH-G2
COPIER> FUNCTION> CCD> DF-LNR
MTF2-M10 MTF value setting 10: main scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting, execute COPIER> FUNCTION> CCD> MTF-CLC.
Display/adj/set range 20 to 85
Unit 0.01
Appropriate target value 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-M11 MTF value setting 11: main scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting, execute COPIER> FUNCTION> CCD> MTF-CLC.
Display/adj/set range 20 to 85
Unit 0.01
Appropriate target value 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
8
Service Mode > COPIER > ADJUST (Adjustment Mode) > CCD
8 Service Mode > COPIER > ADJUST (Adjustment Mode) > CCD
COPIER> ADJUST> CCD
MTF2-M12 MTF value setting 12: main scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting, execute COPIER> FUNCTION> CCD> MTF-CLC.
Display/adj/set range 20 to 85
Unit 0.01
Appropriate target value 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-S10 MTF value setting 10: sub scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting, execute COPIER> FUNCTION> CCD> MTF-CLC.
Display/adj/set range 20 to 85
Unit 0.01
Appropriate target value 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-S11 MTF value setting 11: sub scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting, execute COPIER> FUNCTION> CCD> MTF-CLC.
Display/adj/set range 20 to 85
Unit 0.01
Appropriate target value 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
8-170
8-170