Canon imagePRESS 1135 Series Service Manual page 1222

COPIER > OPTION > NETWORK
DHCP-81 ON/OFF IPaddress dynamic chng in DHCP-81
Lv.2 Details ON/OFF setting for dynamic change of IP address by Option 81 of
DHCP.
Selecting OFF can prevent DHCP packet from including Option 12 or
Option 81 under the packet-monitoring network environment.
Selecting ON enables dynamic change of IP address by Option 81 of
DHCP in the case that the dynamic DNS setting is ON in User Mode.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution Be sure to set ON for the dynamic DNS setting in User Mode to
enable dynamic change of IP address.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
Supplement/memo DHCP: Dynamic Host Configuration Protocol
IFX-CHIG Operatn set by IFAX receive mail content
Lv.1 Details Operation setting according to the number of characters on the
contents of IFAX received mail.
Specifying the number of characters in e-mail (body) text so that the
e-mail (body) text will not be printed at the time of IFAX reception if
e-mail text is less than the specified value.
This machine can output white paper because some senders send
e-mail text consists of linefeed codes only. In such case, specify 2
(number of characters) so that there will be no output of white paper.
In the case of specifying any number other than 0, there will be print/
transfer of header/footer only if the e-mail (body) text is less than the
specified value while no TIFF file is attached.
1 increment of the value increases the number of target characters in
e-mail body text by 1 character.
Use case To reduce print of white paper due to e-mail received by IFAX.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution Be sure to tell the user that there will be no print of e-mail (body) text
if the number of characters is less than the specified value and get
the user's approval.
Display/adj/set range 0 to 999
0: Do not ignore e-mail (body) text
Unit 1 character
Default value 0
Supplement/memo 1 Kanji character is calculated as 2-byte, and the control codes (such
as linefeed code, etc) are included in the number of characters.
8
Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > NETWORK
8 Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > NETWORK
COPIER > OPTION > NETWORK
DNSTRANS Setting of DNS transfer priority
Lv.1 Details Setting of priority order of the protocol (IPv4/IPv6) to be used for
DNS query
In the case of using both IPv6 and IPv4 while the DNS server
supports IPv4, it takes time because of timeout when executing DNS
query with priority on IPv6.
Giving priority on query by IPv4 can shorten the time.
Use case When it takes time to execute DNS query with priority on IPv6
because the DNS server supports IPv4.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: IPv4, 1: IPv6
Default value 1
PROXYRES Setting of proxy response to Windows
Lv.2 Details Set whether to provide proxy response or return the device status
when an inquiry is received via Windows while the device is in sleep
mode.
Use case To correctly execute status response for query from Windows.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: No proxy response, 1: Proxy response
Default value 1
WOLTRANS Setting of sleep recovery protcol
Lv.1 Details Set the protocol for recovery from sleep mode according to the value
of WOL (Wake On LAN) trans.
Reception of a specific network packet is one of the requirements for
the device to recover from sleep mode.
When the number of network protocols supported by the device
increases, the types of network packets which activate recovery from
sleep mode vary. However, there is a possibility that the existing
network protocol is actually used.
Select the type of network packet which activates recovery from
sleep mode according to the environment where the device is used.
Use case To select protocol for sleep recovery.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 1 to 3
1: WSD and SNMP, 2: WSD and CPCA, 3: CPCA and SNMP
Default value 1
8-279
8-279