Canon imagePRESS 1135 Series Service Manual page 1395

SORTER> OPTION
TRM-LMT Fore-edge minimum trim amount: trimmer
Lv.1 Details According to the number of paper stack and the grammage, whether
to set the limit of fore-edge minimum trimming amount of the booklet
trimmer.
Use case When the fore-edge trimming amount is set to small on the thick
paper stack and if trimming failure occurs
Adj/set/operate method Enter the setting value and press OK key.
Caution Actual trimming amount may be larger than the setting value.
Display/adj/set range 0 to 1
0: Fixed (normal), 1: limited
Default value 0
ST1-LMT Set of stack capacity at stack unit: stk
Lv.1 Details To set the stack capacity at the stack unit of the stacker.
As the value is increased by 1, stack capacity is increased by 500
sheets (maximum 5000 sheets).
Setting is applied to both left and right trays.
Use case When setting a limit to the stack capacity of the stack unit
Adj/set/operate method Enter the setting value and press OK.
Display/adj/set range 0 to 9
0: Approx. 5000 sheets, 1: Approx. 4500, ... 8: Approx. 1000, 9:
Approx. 500 sheets
Unit 500 sheets
Default value 0
ST2-LMT Set of stack capacity at stk unit: stk2
Lv.1 Details To set the stack capacity at the stack unit of the secondary stacker.
As the value is increased by 1, stack capacity is increased by 500
sheets (maximum 5000 sheets).
Setting is applied to both left and right trays.
Use case When setting a limit to the stack capacity of the stack unit
Adj/set/operate method Enter the setting value and press OK.
Display/adj/set range 0 to 9
0: Approx. 5000 sheets, 1: Approx. 4500, ... 8: Approx. 1000, 9:
Approx. 500 sheets
Unit 500 sheets
Default value 0
ST1-SLM Set of separator limit at stk unit: stk
Lv.1 Details To set whether to limit the number of separation sheet with same-
width&different-length at the stack unit of the stacker.
When "1" is set, stack over detection is disabled.
Use case When a user has decided that the stackability is fine even though the
limit of separation sheet is removed
Adj/set/operate method Enter the setting value and press OK.
Display/adj/set range 0 to 1
0: Limit, 1: Limitless
Default value 0
8
Service Mode > SORTER > OPTION
8 Service Mode > SORTER > OPTION
SORTER> OPTION
ST2-SLM Set of separator limit at stk unit: stk2
Lv.1 Details To set whether to limit the number of separation sheet with same-
width&different-length at the stack unit of the secondary stacker.
When "1" is set, stack over detection is disabled.
Use case When a user has decided that the stackability is fine even though the
limit of separation sheet is removed
Adj/set/operate method Enter the setting value and press OK.
Display/adj/set range 0 to 1
0: Limit, 1: Limitless
Default value 0
PUCH-SW High-prdctvty/-accurcy punch mode:Fin-AG
Lv.1 Details To switch the high-productivity punch mode or high-accuracy mode
of the finisher.
Use case When switching the high-accuracy mode or high-productivity mode in
punch mode
Adj/set/operate method Select the item and press OK key.
TRY-PATH Tray switch set in non/staple mix:Fin-AF
Lv.1 Details When the tray A is specified as a delivery source in staple/non-
staple mixed, non-stapled paper is delivered from the upper path
and stapled paper is delivered from the lower path so that the tray A
moves up and down frequently and it decreases the productivity.
When "1" is set, even through the tray A is specified as a delivery
source, a part of non-stapled paper is delivered from the lower path
to the tray B. This setting reduces the number to switch the tray while
non-stapled paper may be output to 2 trays separately.
Use case When the tray is switched frequently in staple/non-staple mixed
mode and the productivity is reduced
Adj/set/operate method Select the item and press OK key.
Caution Explain to users that the delivery source for non-stapled paper will
be changed and specify this setting after they agree with it.
Display/adj/set range 0 to 2
0: Tray switch reduction mode OFF, 1: ON, 2: Not use
Default value 1
ALG-IMPR Set Finisher alignment mode: Fin-AG
Lv.1 Details To set the special mode for improving the alignment condition.
Use case When using the special mode for improving the alignment condition
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 20
Appropriate target value 0
Default value 0
8-452
8-452