Canon imagePRESS 1135 Series Service Manual page 1180

COPIER > OPTION > FNC-SW
INTROT-5 Set sheet interval at post-rotatin ctrl5
Lv.1 Details Set the number of sheets between intervals for Execution Control 5
at last rotation (white band).
When the value is incremented by 1, the number of sheets in the
interval is increased by 100 sheets. When the value is set to 0, no
control is executed.
Use case To suit the use environment of the user
Adj/set/operate method Enter the setting value and press the OK key.
Caution When the number of sheets is increased (when the interval is
increased), the image failure occurrence ratio is increased.
Display/adj/set range 0 to 255
0: No control is executed.
Unit 100 sheets
Default value 10
MIXM-PFP Productivty priority mode in media mixed
Lv.1 Details To set the productivity priority mode in media mixed situation.
Normally, productivity is reduced as the media is switched due to
engine adjustment.
As "1" (productivity priority mode) is set, media information is notified
to DC controller before printing start and media normal speed is
realized.
Use case To prevent the productivity from being reduced in media mixed
situation.
Adj/set/operate method Enter the setting value and press OK key.
Display/adj/set range 0 to 1
0: Normal mode, 1: Productivity priority mode
Default value 0
RHDD-SW Setting of Removable HDD installation
Lv.1 Details Setting for installation condition of Removable HDD (Removable
HDD Kit).
Select 1 (installed) when installing the Removable HDD. Select 0 (not
installed) when removing the Removable HDD.
Use case When installing/removing Removable HDD.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: Not installed, 1: Installed
Default value 0
JAMEXIT Setting of jam automatic ejection
Lv.1 Details To set whether to eject jammed paper automatically.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: ON, 1: OFF
Default value 0
8
Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > FNC-SW
8 Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > FNC-SW
COPIER > OPTION > FNC-SW
MIB-NVTA RFC-compatible character stringMIB write
Lv.1 Details As default, MIB object which NVT-ASCII can be written exists in
order to link with LUI entry value. This violates RFC order, so a
problem like garbled 2-byte characters may occur in the SNMP
monitoring system, such as the 3rd vendor's MPS.
Whether non-RFC-compatible character strings are written in MIB
can be set using this mode.
When 1 is set, only the character strings which are strictly compatible
with RFC are written. (Writing operation is executed from the SNMP
manager.) LUI is not linked.
Use case Upon user's request (operation with RFC-compatible system)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 3
0: Compatible in a conventional manner, 1: RFC-compatible, 2 to 3:
Not used
Default value 0
Supplement/memo RFC: Document of internet-related technical standards
NVT-ASCII: Network Virtual Terminal-ASCII
GRP-SEP Set job separator b/w copies: group sort
Lv.2 Details To set whether to insert the job separator with every specified
number of sheets at copy with group sort.
The paper source and paper interval of the job separator to be
inserted are accorded with the user mode (Additional Functions>
Common Settings> Job Separator between Copies).
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adjust/set range 0 to 1
0: Not inserted, 1: Inserted
Default value 0
Related user mode Additional Functions> Common Settings> Job Separator between
Copies
JM-ERR-D Set of error display of 0CAx jam (DCON)
Lv.2 Details To set whether to display "0CAF" jam as the error "E996-0CAF".
In the case of a jam, log cannot be obtained depending on the timing.
By selecting 1 when the jam "0CAF" occurs, it is displayed as the
error "E996-0CAF" so that the log can be obtained.
Use case When obtaining a log at the occurrence of 0CAF jam
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: Display as a jam, 1: Display as an error
Default value 0
Related service mode COPIER> OPTION> FNC-SW> JM-ERR-R
8-237
8-237