Canon imagePRESS 1135 Series Service Manual page 1240

COPIER > OPTION > USER
DK2-ASST Air heater setting of POD upper deck
Lv.1 Details Set the condition to turn on the paper separation air heater at the
POD upper deck.
When the media is switched from non-coated paper to coated paper,
paper pickup operation does not start until the temperature of the
paper separation air heater reaches the specified temperature.
To shorten the wait time, make a setting of "Not dependent on the
media".
When the use environment is near the threshold for turning ON/
OFF the heater, switching occurs frequently, which increases the
wait time. To shorten the wait time, make a setting of turning on the
heater constantly.
Use case When it is requested to shorten the wait time
Adj/set/operate method 1) Enter the setting value and press the OK key.
2) Turn OFF/ON the main power.
Caution • To make a setting of "Not dependent on the media", be sure to
receive approval from the user in advance after explaining that
there is a possibility that transfer performance for non-coated
paper may decrease.
• To make a setting of turning on the heater constantly, be sure to
receive approval from the user in advance after explaining that
there is a possibility that transfer performance may decrease when
humidity decreases.
Display/adj/set range 0 to 2
0: Dependent on the media and environment condition
1: Dependent on the environment condition (Not dependent on the
media)
2: Turning on the heater constantly (Not dependent on environment/
media)
Default value 0
Related service mode COPIER> OPTION> USER> DK1-ASST, DK3-ASST to DK10ASST
DK9-BSTP Float fan stop set in POD3 mid deck oprn
Lv.1 Details Turn off the paper separation fan when an image formation request
was not made even after the timing of the request has elapsed
during continuous operation of the second tandem POD middle deck.
Make a setting of "after how many seconds the fan is turned off when
the timing of the request has elapsed".
Use case Change the setting value to change the time until turning off the
paper separation fan which has been operating continuously.
Adj/set/operate method 1) Enter the setting value and press the OK key.
2) Turn OFF/ON the main power.
Display/adj/set range 0 to 20
Unit 1 second
Default value 20
Related service mode COPIER> OPTION> USER> DK1-BSTP to DK8-BSTP, DK10BSTP
8
Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > USER
8 Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > USER
COPIER > OPTION > USER
DK1-BSTP Float fan stop set in host deck operatin
Lv.1 Details Turn off the paper separation fan when an image formation request
was not made even after the timing of the request has elapsed
during continuous operation of the main unit deck. Make a setting of
"after how many seconds the fan is turned off when the timing of the
request has elapsed".
Use case Change the setting value to change the time until turning off the
paper separation fan which has been operating continuously.
Adj/set/operate method 1) Enter the setting value and press the OK key.
2) Turn OFF/ON the main power.
Display/adj/set range 0 to 20
Unit 1 second
Default value 20
Related service mode COPIER> OPTION> USER> DK2-BSTP to DK10BSTP
DK2-BSTP Float fan stop set in POD uper deck oprn
Lv.1 Details Turn off the paper separation fan when an image formation request
was not made even after the timing of the request has elapsed
during continuous operation of the POD upper deck. Make a setting
of "after how many seconds the fan is turned off when the timing of
the request has elapsed".
Use case Change the setting value to change the time until turning off the
paper separation fan which has been operating continuously.
Adj/set/operate method 1) Enter the setting value and press the OK key.
2) Turn OFF/ON the main power.
Display/adj/set range 0 to 20
Unit 1 second
Default value 20
Related service mode COPIER> OPTION> USER> DK1-BSTP, DK3-BSTP to DK10BSTP
DK3-BSTP Float fan stop set in POD mid deck oprn
Lv.1 Details Turn off the paper separation fan when an image formation request
was not made even after the timing of the request has elapsed
during continuous operation of the POD middle deck. Make a setting
of "after how many seconds the fan is turned off when the timing of
the request has elapsed".
Use case Change the setting value to change the time until turning off the
paper separation fan which has been operating continuously.
Adj/set/operate method 1) Enter the setting value and press the OK key.
2) Turn OFF/ON the main power.
Display/adj/set range 0 to 20
Unit 1 second
Default value 20
Related service mode COPIER> OPTION> USER> DK1-BSTP to DK2-BSTP, DK4-BSTP
to DK10BSTP
8-297
8-297