Canon imagePRESS 1135 Series Service Manual page 1235

COPIER > OPTION > USER
MAIL-OF Mail send prohibition to entered address
Lv.1 Details Setting to prohibit address entry at the time of e-mail transmission.
File transmission is not available by entering the address because of
no display of "e-mail" on the transmission screen.
The addresses already registered in the address book can be used.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution To restrict addresses for transmission, be sure to manually delete
them because the addresses registered in the address book can be
used.
Display/adj/set range 0 to 1
0: Allow, 1: Prohibit
Default value 0
IFAX-OF IFAX send prohibition to entered address
Lv.1 Details Setting to prohibit address entry at the time of IFAX transmission.
File transmission is not available by entering the address because of
no display of "IFAX" on the transmission screen.
The addresses already registered in the address book can be used.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution To restrict addresses for transmission, be sure to manually delete
them because the addresses registered in the address book can be
used.
Display/adj/set range 0 to 1
0: Allow, 1: Prohibit
Default value 0
LDAP-DEF Initial conditn set of LDAPserver search
Lv.1 Details Setting of initial (default) condition for search target attribute specified
when searching details of LDAP server.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 6
0: Name, 1: E-mail, 2: FAX, 3: Organization, 4: Organization unit,
5: No registration 1 (any setting), 6: No registration 2 (any setting)
Default value 0
Related service mode COPIER> OPTION> USER> LDAP-SW
8
Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > USER
8 Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > USER
COPIER > OPTION > USER
DK3-ASST Air heater setting of POD middle deck
Lv.1 Details Set the condition (media/environment) to turn on the paper
separation air heater at the POD middle deck.
When the media is switched from non-coated paper to coated paper,
paper pickup operation does not start until the temperature of the
paper separation air heater reaches the specified temperature.
To shorten the wait time, make a setting of "Not dependent on the
media".
When the use environment is near the threshold for turning ON/
OFF the heater, switching occurs frequently, which increases the
wait time. To shorten the wait time, make a setting of turning on the
heater constantly.
Use case When it is requested to shorten the wait time
Adj/set/operate method 1) Enter the setting value and press the OK key.
2) Turn OFF/ON the main power.
Caution • To make a setting of "Not dependent on the media", be sure to
receive approval from the user in advance after explaining that
there is a possibility that transfer performance for non-coated
paper may decrease.
• To make a setting of turning on the heater constantly, be sure to
receive approval from the user in advance after explaining that
there is a possibility that transfer performance may decrease when
humidity decreases.
Display/adj/set range 0 to 2
0: Dependent on the media and environment condition
1: Dependent on the environment condition (Not dependent on the
media)
2: Turning on the heater constantly (Not dependent on environment/
media)
Default value 0
FREE-DSP Dspl/hide of charge disable screen
Lv.2 Details Setting to display/hide the charge-disabling screen for switching
between charge and no charge.
The hardware switch for switching charge/no charge in the coin
manager enables the mode in which all the service is available for
free (store manager mode) by temporarily resetting the charging
system.
Without the hardware switch, the setting to display the charge-
disabling screen with Additional Functions button enables switch of
the mode with software switch.
Use case To enable all the service to be provided for free by temporarily
resetting charging system.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: Hide (no display), 1: Display
Default value 0
8-292
8-292