Canon imagePRESS 1135 Series Service Manual page 1377

SORTER> ADJUST
ST2-ALT2 Left tray push-on pstn in feed way: stk2
Lv.1 Details To adjust the push-on position in feed direction of left tray on the
stack unit of secondary stacker.
As the value is increased by 1, the push-on position moves by
0.15 mm.
+: toward front (narrow)
-: toward rear (widen)
Use case Restore the position to the factory setting when EEPROM/master
controller PCB is replaced
Adj/set/operate method Enter the setting value and press OK key.
Display/adj/set range -34 to 34
Unit 0.15 mm
Default value 0
ST1-ALT3 Both tray push-on pstn in feed way: stk
Lv.1 Details To adjust the push-on position in feed direction of both tray on the
stack unit of stacker.
As the value is increased by 1, the push-on position moves by
0.15 mm.
+: toward front (narrow)
-: toward rear (widen)
Use case Restore the position to the factory setting when EEPROM/master
controller PCB is replaced.
Adj/set/operate method Enter the setting value and press OK key
Display/adj/set range -34 to 34
Unit 0.15 mm
Default value 0
ST2-ALT3 Both tray push-on pstn in feed way: stk2
Lv.1 Details To adjust the push-on position in feed direction of both tray on the
stack unit of secondary stacker.
As the value is increased by 1, the push-on position moves by
0.15 mm.
+: toward front (narrow)
-: toward rear (widen)
Use case Restore the position to the factory setting when EEPROM/master
controller PCB is replaced.
Adj/set/operate method Enter the setting value and press OK key
Display/adj/set range -34 to 34
Unit 0.15 mm
Default value 0
8
Service Mode > SORTER > ADJUST
8 Service Mode > SORTER > ADJUST
SORTER> ADJUST
ST2-ALT1 Rght tray push-on pstn in feed way: stk2
Lv.1 Details To adjust the push-on position in feed direction of right tray on the
stack unit of secondary stacker.
As the value is increased by 1, the push-on position moves by
0.15 mm.
+: toward front (narrow)
-: toward rear (widen)
Use case Restore the position to the factory setting when EEPROM/master
controller PCB is replaced
Adj/set/operate method Enter the setting value and press OK key.
Display/adj/set range -34 to 34
Unit 0.15 mm
Default value 0
PF-A3Z1 Adj of A3 Z-fold position (1st): PFU
Lv.1 Details Adjust the 1st fold position of A3 paper Z-fold position of the paper
folding unit.
Increase the input value by 1, the fold position will move by 0.1 mm.
+ :
- :
Use case If the fold position adjustment in additional function mode is
inadequate
Adj/set/operate method Enter the setting value and press OK key.
Display/adj/set range -128 to 127
Unit 0.1 mm
Appropriate target value 0
Default value 0
PF-A3Z2 Adj of A3 Z-fold position (2nd): PFU
Lv.1 Details Adjust the 2nd fold position of A3 paper Z-fold position of the paper
folding unit.
Increase the input value by 1, the fold position will move by 0.1 mm.
+ :
- :
Use case If the fold position adjustment in additional function mode is
inadequate
Adj/set/operate method Enter the setting value and press OK key.
Display/adj/set range -128 to 127
Unit 0.1 mm
Appropriate target value 0
Default value 0
8-434
8-434