Canon imagePRESS 1135 Series Service Manual page 1257

COPIER> OPTION> LCNS-TR
ST-PDFDR Install state dspl of Direct Print PDF
Lv.2 Details To display installation state of Direct Print PDF when transfer is
disabled.
Use case When checking whether Direct Print PDF is installed
Adj/set/operate method 1) Select ST-PDFDR.
2) Enter 0, and then press OK key.
When installation has been completed, the transfer license key is
displayed under TR-PDFDR.
Display/adj/set range When operation finished normally: OK!
Default value 0
TR-PDFDR Trns lcns key dspl of Direct Print PDF
Lv.2 Details To display transfer license key to use Direct Print PDF when transfer
is disabled.
Use case • When replacing HDD
• When replacing the device
Adj/set/operate method 1) Select ST-PDFDR.
2) Enter 0, and then press OK key.
The transfer license key is displayed under TR-PDFDR.
Display/adj/set range 24 digits
ST-SCR Install state dspl of Encry Secure Print
Lv.2 Details To display installation state of Encrypted Secure Print when transfer
is disabled.
Use case When checking whether Encrypted Secure Print is installed
Adj/set/operate method 1) Select ST-SCR.
2) Enter 0, and then press OK key.
When installation has been completed, the transfer license key is
displayed under TR-SCR.
Display/adj/set range When operation finished normally: OK!
Default value 0
TR-SCR Trns license key dspl of Encry Secure Pnt
Lv.2 Details To display transfer license key to use Encrypted Secure Print when
transfer is disabled.
Use case • When replacing HDD
• When replacing the device
Adj/set/operate method 1) Select ST-SCR.
2) Enter 0, and then press OK key.
The transfer license key is displayed under TR-SCR.
Caution This mode is enabled when there is "3DES+USH-H" Board.
Display/adj/set range 24 digits
8
Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > LCNS-TR
8 Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > LCNS-TR
COPIER> OPTION> LCNS-TR
ST-HDCLR Installation state display of Data Erase
Lv.2 Details To display installation state of Data Erase (for old model) when
transfer is disabled.
Use case When checking whether Data Erase (for old model) is installed
Adj/set/operate method 1) Select ST-HDCLR.
2) Enter 0, and then press OK key.
When installation has been completed, the transfer license key is
displayed under TR-HDCLR.
Display/adj/set range When operation finished normally: OK!
Default value 0
TR-HDCLR Transfer license key dspl of Data Erase
Lv.2 Details To display transfer license key to use Data Erase (for old model)
when transfer is disabled.
Use case • When replacing HDD
• When replacing the device
Adj/set/operate method 1) Select ST-HDCLR.
2) Enter 0, and then press OK key.
The transfer license key is displayed under TR-HDCLR.
Caution This mode is enabled when there is "3DES+USH-H" Board.
Display/adj/set range 24 digits
ST-BRDIM Install state dspl: PCL Barcode Printing
Lv.2 Details To display installation state of Barcode Printing for PCL when transfer
is disabled.
Use case When checking whether Barcode Printing for PCL is installed
Adj/set/operate method 1) Select ST-BRDIM.
2) Enter 0, and then press OK key.
When installation has been completed, the transfer license key is
displayed under TR-BRDIM.
Display/adj/set range When operation finished normally: OK!
Default value 0
TR-BRDIM Trns lcns key dspl: PCL Barcode Printing
Lv.2 Details To display transfer license key to use Barcode Printing for PCL when
transfer is disabled.
Use case • When replacing HDD
• When replacing the device
Adj/set/operate method 1) Select ST-BRDIM.
2) Enter 0, and then press OK key.
The transfer license key is displayed under TR-BRDIM.
Display/adj/set range 24 digits
8-314
8-314