Pacific Power Source AFX Series Operation Manual page 7

Programmable power source
Hide thumbs Also See for AFX Series:
Table of Contents

Advertisement

8.3
Calibration Commands ........................................................................................................................ 217
8.3.1
AFX Calibration Commands ........................................................................................................................... 217
8.3.2
UPC Mode Specific commands. ..................................................................................................................... 219
8.3.3
AUX I/O Interface Calibration Commands .................................................................................................... 219
8.4
Measurement Commands .................................................................................................................. 220
8.4.1
Voltage Measurement Commands ............................................................................................................... 220
8.4.2
Frequency Measurement Commands .......................................................................................................... 221
8.4.3
Current Measurement Commands ............................................................................................................... 221
8.4.4
Power Measurement Commands ................................................................................................................. 223
8.4.5
KWh Measurement Commands .................................................................................................................... 223
8.4.6
Other Measurement Commands .................................................................................................................. 225
8.4.7
Measurement Data Logging Commands ...................................................................................................... 225
8.4.8
Waveform Capture Commands ..................................................................................................................... 229
8.4.9
Harmonic Measurements Commands .......................................................................................................... 231
8.5
Output Control Commands ................................................................................................................ 236
8.6
Program Commands ........................................................................................................................... 240
8.6.1
Program Control Commands ......................................................................................................................... 240
8.6.2
Execution Commands..................................................................................................................................... 251
8.6.3
Transient Segments Commands .................................................................................................................... 252
8.6.4
Memory Management Commands ............................................................................................................... 257
8.7
Source Commands .............................................................................................................................. 260
8.7.1
Source Configuration Programming Commands .......................................................................................... 260
8.7.2
Voltage Programming Commands ................................................................................................................ 265
8.7.3
Frequency Programming Commands............................................................................................................ 272
8.7.4
Current Programming Commands ................................................................................................................ 274
8.7.5
Phase Programming Commands ................................................................................................................... 276
8.7.6
Waveform Programming Commands ........................................................................................................... 278
8.7.7
Voltage Protection Programming Commands .............................................................................................. 286
8.7.8
Current Protection Programming Commands .............................................................................................. 288
8.7.9
Power Protection Programming Commands ................................................................................................ 292
8.7.10
Impedance Programming Commands .......................................................................................................... 298
8.7.11
STEP Transient Commands ............................................................................................................................ 301
8.7.12
PULSE Transient Commands .......................................................................................................................... 321
8.7.13
IEC413 Option Interharmonics Commands .................................................................................................. 332
8.8
Status Commands ............................................................................................................................... 336
8.9
System Commands .............................................................................................................................. 338
8.9.1
System Error Commands ............................................................................................................................... 338
8.9.2
System Information Commands .................................................................................................................... 339
8.9.3
System Interface Commands ......................................................................................................................... 342
8.9.4
System Configuration Commands ................................................................................................................. 346
8.9.5
Parallel System Commands ............................................................................................................................ 348
8.9.6
System Sanitization Commands .................................................................................................................... 349
8.9.7
Communication LAN Commands .................................................................................................................. 349
8.9.8
Communication Serial Port Commands ........................................................................................................ 354
8.9.9
Communication USB Commands .................................................................................................................. 356
8.9.10
Communication GPIB Commands ................................................................................................................. 357
8.9.11
System Firmware Commands ........................................................................................................................ 359
8.9.12
System Remote Access Commands .............................................................................................................. 360
8.9.13
Miscellaneous System Commands ................................................................................................................ 362
8.10
Auxiliary I/O System Commands ........................................................................................................ 363
8.10.1
System Analog & Digital IO Commands ........................................................................................................ 363
8.10.2
SOURce:SYNChronize Commands ................................................................................................................. 376
8.10.3
PROGram:TRANsient Triggers Commands ................................................................................................... 379
8.10.4
AUX I/O Calibration Commands .................................................................................................................... 381
Entire Contents Copyright
2018 by Pacific Power Source, Inc. (PPS) • All Rights Reserved • No reproduction without written authorization from PPS.
AFX Series Power Source Operation Manual
AFX SERIES® OPERATION MANUAL
Page 7 of 485
CONTENTS

Hide quick links:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AFX Series and is the answer not in the manual?

Subscribe to Our Youtube Channel

Table of Contents