Program Example - Omron CS1W-MCH71 Operation Manual

The section provides a programming example to demonstrate how the CJ1W-MCH71 and CS1W-MCH71 Motion Control
Units can be used.

10-1 Program Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10-1-1 Positioning with PTP Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-1-2 Positioning with Linear Interpolation . . . . . . . . . . . . . . . . . . . . . . . .
10-1-3 Positioning with Linear and Circular Interpolation. . . . . . . . . . . . . .
10-1-4 Positioning with Position Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-1-5 Positioning with Workpiece Coordinate System with Subprograms
10-1-6 Positioning with Changing Interpolation Acceleration Time Parameter 580
10-1-7 Positioning with Position Data Calculation . . . . . . . . . . . . . . . . . . .
10-1-8 Stopping a Program with General Input . . . . . . . . . . . . . . . . . . . . . .
10-1-9 Stopping Operation with Optional End Using General Input and
Assigning Position Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-1-10 Positioning of Turntable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-1-11 Feeder Feeding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-1-12 Starting Peripherals during Axis Movement . . . . . . . . . . . . . . . . . . .
10-1-13 High-speed Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-1-14 Interrupt Feeding (MOVEI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-1-15 Time-specified Positioning (MOVET) . . . . . . . . . . . . . . . . . . . . . . .
10-1-16 Regular Winding to Rough Winding (MOVETRAV) . . . . . . . . . . . .
10-1-17 Electronic Cam, Single Axis (CAM) . . . . . . . . . . . . . . . . . . . . . . . .
10-1-18 Link Operation (MOVELINK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-1-19 Electronic Cam, Synchronous (CAMBOX) . . . . . . . . . . . . . . . . . . .
10-1-20 Electronic Shaft (CONNECT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-1-21 Trailing Synchronization/Synchronization Cancel (SYNC/SYNCR)
10-1-22 Travel Distance Superimpose/Travel Distance Superimpose Cancel
(ADDAX/ADDAXR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-1-23 Speed Control/Speed Control Cancel (SPEED/SPEEDR) . . . . . . . .
10-1-24 Torque Control/Torque Control Cancel (TORQUE/TORQUER) . . .
10-1-25 Target Position Change (MOVEMODI) . . . . . . . . . . . . . . . . . . . . . .
10-1-26 Present Position Latch (LATCH) . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-1-27 Single Block Ignored (NSTOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-1-28 Parallel Execution (PARALLEL, JOINT, JWAIT) . . . . . . . . . . . . . .
10-1-29 Selective Execution (SWITCH, CASE, BREAK, SEND) . . . . . . . .
10-2 Slave Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-2-1 Using 64-Point I/O Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-2-2 Using Counter Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-2-3 Using Pulse Output Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-3 Others. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 10
Program Example
574
574
575
576
577
578
581
583
583
584
586
587
588
589
590
591
592
594
595
596
597
598
600
601
602
603
604
605
606
607
607
608
612
619
573