Korg Electronic Keyboard Parameter Manual page 520

Sequencer mode
On (checked): The Bus Select, FX Control Bus, Send1,
and Send2 settings for each key of the selected drum
kit will be used. Check this setting if you want to apply
an individual insert effect to each drum instrument, or
to send individual drum instruments to AUDIO
OUTPUT (INDIVIDUAL).
Tip: In most preloaded drumkits, the drum
instruments have the same Bus Select settings
according to their type, as follows.
Snares → IFX1
Kicks → IFX2
Toms → IFX3
Cymbals → IFX4
Percussion etc. → IFX5
If you want to edit these routings, use the "Drum Kit
IFX Patch" page menu command. For details, see
"Drum Kit IFX Patch" on page 410.
Off (unchecked): The Bus Select, FX Control Bus, and
Send 1/2 settings will be used. All drum instruments
will be sent to the specified bus.
Bus Select (IFX/Indiv.Out Assign)
[L/R, IFX1...12, 1...8, 1/2...7/8, Off]
This specifies the output bus for the track's program
oscillator. This parameter can also be edited from the
P8– MIDI Routing 2 page.
L/R: Output to the L/R bus.
IFX1...12: Output to the IFX1–12 buses.
1...8: The track will be output in mono from the
corresponding AUDIO OUTPUT (INDIVIDUAL).
1/2...7/8: The track will be output in stereo according to
its pan setting from the corresponding AUDIO
OUTPUT (INDIVIDUAL) pairs 1/2, 3/4, 5/6, or 7/8.
Off: The track will not be output from the L/R bus,
IFX1–12 buses, or Individual 1–8 buses. Choose the Off
setting if you want the program oscillator output of the
track to be connected in series to a master effect. Use
Send1 (to MFX1) and Send2 (to MFX2) to specify the
send levels.
Tip: You can create a wide variety of routings by using
each track's Bus Select and the Chain to and Chain
settings (8–5a) that follow the insert effect.
Send1 (MFX1)
Send2 (MFX2)
For each track, these parameters set the send level to
master effects 1 and 2. These settings are valid when
Bus Select is set to L/R or Off. When IFX 1–12 are
selected, the send levels to master effects 1 and 2 are set
by the Send1 and Send2 parameters of the Insert FX
page, after the sound has passed through IFX1–12.
If Bus Select is set to 1...8 or 1/2...7/8, these settings
are ignored.
The Send 1 and 2 setting you specify here are used
when playing-back or recording from the beginning of
the song. If you modify these settings during
recording, your changes will be recorded as
performance data; the send amounts will change
accordingly during playback. You can also modify
510
these settings during playback. However if Send 1 and
2 data has been recorded, the settings will change
according to the recorded data.
Note: You can use the control surface to control Send1
and Send2. These can also be controlled from the mixer
section of the front panel, or from the P0– Control
Surface page of the LCD screen. The procedure given
below describes how to make these settings from the
front panel.
1. Press the CONTROL ASSIGN MIXER
TIMBRE/TRACK switch to select either tracks 1–8
or 9–16.
2. Press the MIXER KNOBS switch to select
CHANNEL STRIP.
3. Use the MIXER SELECT 1/9–8/16 switches to select
the track whose send levels you want to adjust.
4. Use MIX CHANNEL STRIP "FX SEND 1" (knob 7)
and "FX SEND 2" (knob 8) to control the send
levels.
If Bus Select (IFX/Indiv. Out Assign) is set to L/R
or Off, this will control "Send1 (MFX1)"–"Send2
(MFX2)." If Bus Select (IFX/Indiv. Out Assign) is
set to IFX1–12, this will control Send1 and Send2
(P8– Insert FX page).
If Status (2–1a) is either INT or BTH, CC#93 and
#91 can be received to control send 1 and 2
respectively and change their settings. When you
switch songs or return to the beginning of a song,
tracks whose Status is EXT, EX2 or BTH will
transmit these settings via MIDI. This data will be
transmitted on the MIDI channel of each track as set
by MIDI Channel (2–1a). The actual send level is
determined by multiplying the value of these
parameters with the send level settings of the
oscillator(s) of the program used by the track
(Send1 and "Send2," Program 8–1d).
Track 02...16 (Track Number)
These settings specify the program oscillator output
bus and master effect send levels for MIDI tracks 2
through 16. They are the same as for track 1. See "Track
01":.
▼ 8–1: Page Menu Commands
[000...127] The number before each command shows its ENTER +
number-key shortcut. For more information on these
[000...127]
shortcuts, see "ENTER + 0-9: shortcuts for menu
commands" on page 138.
• 0: Memory Status. For more information, see
"Memory Status" on page 524.
• 1: Exclusive Solo. For more information, see
"Exclusive Solo" on page 138.
• 2: Copy Insert Effect. For more information, see
"Copy Insert Effect" on page 149.
• 3: Swap Insert Effect. For more information, see
"Swap Insert Effect" on page 150.
• 4: Drum Kit IFX Patch. For more information, see
"Drum Kit IFX Patch" on page 410.