043: Multitap Cho/Delay 4Taps - Korg Electronic Keyboard Parameter Manual

MODULATION
L Pre Delay [msec]
Sets the delay time for the left channel. p.797.
R Pre Delay [msec]
Sets the delay time for the right channel. p.797.
Depth1
Sets the depth of LFO1 modulation.
Depth2
Sets the depth of LFO2 modulation.
Source
Selects the modulation source of LFO1&2 modulation
depth.
Amount1
Sets the modulation amount of LFO1 modulation
depth.
Amount2
Sets the modulation amount of LFO2 modulation
depth.
Feedback
Sets the feedback amount. p.798.
High Damp [%]
Sets the damping amount in the high range.
LFO1/2
LFO1
Depth1
LFO2
Depth2
LFO1 Waveform
Selects the waveform for LFO1.

043: Multitap Cho/Delay 4Taps

This effect has four chorus blocks, each with a different
LFO phase. You can create a complex stereo image by
setting each block's delay time, depth, output level,
and pan individually. You can also fix some of the
chorus blocks to combine the chorus and delay effects.
Chorus, Flanger, and Phaser
[0.0...50.0]
[0.0...50.0]
[0...100]
[0...100]
[Off...Tempo]
[+/–100]
[+/–100]
[+/–100]
[0...100]
Bi-Phase Modulation LFO
+
[Triangle, Sine]
043: Multitap Cho/Delay 4Taps
LFO2 Waveform
Selects the waveform for LFO2.
Phase Sw
This lets you invert the LFO phase between the left and
right channels.
LFO1 Frequency [Hz]
This sets the speed of LFO1, in Hz.
LFO2 Frequency [Hz]
This sets the speed of LFO2, in Hz.
Source
Selects a source to modulate the speeds of LFO1 & 2.
LFO1 Amount
This sets the LFO1 Frequency modulation amount, in
Hz.
LFO2 Amount
This sets the LFO2 Frequency modulation amount, in
Hz.
LFO1 Type [Individual, Common1, Common2]
This controls whether the effect uses its individual
LFO1, or one of the Common FX LFOs. For more
information, see "LFO Type" on page 777.
Common LFO Phase Offset [degrees]
When Type is set to Common FX LFO 1 or 2, this lets
you offset the phase from the master LFO.
LFO2 Type [Individual, Common1, Common2]
This controls whether the effect uses its individual
LFO2, or one of the Common FX LFOs. For more
information, see "LFO Type" on page 777.
Common LFO Phase Offset [degrees]
When Type is set to Common FX LFO 1 or 2, this lets
you offset the phase from the master LFO.
OUTPUT
This is the standard effects output section, with
modulatable control over wet/dry balance. For more
information, see "OUTPUT" on page 764.
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left
Feedback
Tap1 Delay
Tap2 Delay
+
Tap3 Delay
Tap4 Delay
Right
0 [degree]
180 [degree]
90 [degree]
270 [degree]
LFO: Triangle
[Triangle, Sine]
[0 degree, 180 degree]
[0.02...30.00]
[0.02...30.00]
[Off...Tempo]
[–30.00...+30.00]
[–30.00...+30.00]
[+/–180]
[+/–180]
Wet / Dry
Level
Pan
Level
Pan
Level
Pan
Level
Pan
Wet / Dry
799