Table of Contents
Advertisement
Global mode
L/R: The input signal will be sent to the L/R bus.
IFX1...12: The input signal will be sent to the IFX1–12
bus. Choose one of these settings if you want to apply
an insert effect while sampling.
1...8: The input signal will be sent to the specified
INDIVIDUAL OUTPUT in monaural. The Pan setting
will be ignored.
1/2...7/8: The input signal will be sent in stereo
(including the effect of the Pan control) to the specified
INDIVIDUAL OUTPUT pair.
Off: The input signal will not be routed directly to the
outputs or Insert Effects. However, it may still be
routed to an FX Control Bus or REC Bus.
FX Ctrl Bus (FX Control Bus)
This sends the external audio input signal to an FX
Control bus (two stereo channels; FX Ctrl 1 and 2).
For details, see ""8–1d: FX Control Bus" on page 124.
REC Bus
This sends the external audio input signal to the REC
buses (four mono channels; 1, 2, 3, 4).
Use the REC buses when you want to sample in
various modes or to record audio tracks in Sequencer
mode. These are dedicated buses for recording.
Off: The external audio signal will not be sent to the
REC buses. Normally you will use the Off setting.
1, 2, 3, 4: The external audio input signal will be sent to
the specified REC bus. The Pan setting is ignored, and
the signal is sent in monaural.
1/2, 3/4: The external audio input signal will be sent in
stereo to the specified pair of REC buses. The Pan
setting sends the signal in stereo to buses 1 and 2 or
buses 3 and 4.
Send1 (to MFX1)
Send2 (to MFX2)
These adjust the levels at which the external audio
input signal is sent to the master effects.
Send1 (to MFX1): Send the signal to master effect 1.
Send2 (to MFX2): Send the signal to master effect 2.
This setting is ignored if Bus Select is other than L/R
or Off.
If Bus Select (IFX/Indiv.) is set to IFX1–12, the send
levels to the master effects are set by the post-IFX1–12
Send1 and Send2 (Program, Combination, Sequencer
8–5a).
Note: You can use the control surface to control Send1
(to MFX1) and Send2 (to MFX2). You can also make
this setting from the front panel mixer section or from
the P0– Control Surface screen of the LCD.
If Bus Select (IFX/Indiv.) is set to other than Off,
and you raise the Level setting, the external audio
source will be input to the OASYS. At this time if
audio cables are connected to the AUDIO INPUT 1–
4 jacks, the noise component will be input via the
AD converters into the OASYS even if there is no
audio input, and depending on the settings, may be
output from the AUDIO OUTPUT L/R, 1–8 jacks. If
you want to perform using only internal sounds
648
[Off, 1, 2]
[Off, 1, 2, 3, 4, 1/2, 3/4]
[000...127]
[000...127]
such as programs, combinations, and songs, and are
not using external audio inputs, you should set Bus
Select (IFX/Indiv.) to Off, or set Level to 0.
As with REC Bus and FX Control Bus, turn this off
if you're not using it.
PLAY/MUTE
This indicates the PLAY or MUTE status of each
external audio signal input. The settings can be
switched from the control surface.
PLAY: The external audio signal will be input as
specified by the various parameters.
MUTE: The external audio signal will be muted
(silent), and will not be input.
Note: You can control PLAY/MUTE from the control
surface. You can also make this setting from the front
panel mixer section or from the P0– Control Surface
page of the LCD.
SOLO ON/OFF
This indicates the SOLO status of each external audio
signal input. The settings can be switched from the
control surface.
Sound will be output only from channels whose status
is SOLO ON. Other channels will be muted.
In Program mode, oscillators will be soloed. In
Combination mode, timbres will be soloed. In
Sequencer mode, MIDI tracks and audio tracks will be
soloed.
The operation will depend on the Exclusive Solo page
menu command setting in each mode.
Exclusive Solo Off: Multiple channels can be soloed.
The solo status will change each time you press SOLO
ON/OFF.
Exclusive Solo On: When you press SOLO ON/OFF,
only that channel will be soloed.
Note: You can control SOLO ON/OFF from the control
surface. You can also make this setting from the front
panel mixer section or from the P0– Control Surface
page of the LCD.
The SOLO setting is not memorized when you
Write.
Pan
This specifies the panning of the external audio input
signal. When inputting a stereo audio source, you will
normally set the inputs to L000 and R127 respectively.
Note: You can control Pan from the control surface. You
can also make this setting from the front panel mixer
section or from the P0– Control Surface page of the
LCD.
Level
Specifies the level of the external audio signal that will
be input. Normally you will set this at 127.
Note: You can control volume from the control surface.
You can also make this setting from the front panel
mixer section or from the P0– Control Surface page of
the LCD.
[(Off, On)]
[L000...C064...R127]
[000...127]
Advertisement
Table of Contents
