044: Multitap Cho/Delay 6Taps - Korg Electronic Keyboard Parameter Manual

Effect Guide
MOD DELAY
Taps 1-4
There are four delay taps, each with separate settings
for delay time, chorus depth, level, and pan. The
chorus LFO phases are different for each tap:
Tap 1 = 0 degrees
Tap 2 = 180 degrees
Tap 3 = 90 degrees
Tap 4 = 270 degrees
Tap 1...4 [msec]
This sets the tap's delay time.
Depth 1...4
This sets the tap's chorus depth.
Level 1...4
This sets the tap's output level.
Pan 1...4
This sets the tap's stereo position.
Tap 1 Feedback
Tap1 Feedback
Sets the Tap1 feedback amount.

044: Multitap Cho/Delay 6Taps

This effect has six chorus blocks with different LFO
phases. You can produce a complex stereo image by
setting a different delay time and depth for each block.
You can control the delay output level via a
modulation source.
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left
Feedback
+
Right
0 [degree]
180 [degree]
60 [degree]
240 [degree]
120 [degree]
300 [degree]
LFO: Triangle
D -mod
On/Off Control
MODULATION DELAY
Taps 1-6
There are six delay taps, each with separate settings for
delay time, chorus depth, and on/off/modulation
status. The chorus LFO phases are different for each
tap:
Tap 1 = 0 degrees
Tap 2 = 180 degrees
Tap 3 = 60 degrees
Tap 4 = 240 degrees
800
[0...1000]
[0...30]
[0...30]
[L6...L1, C, R1...R6]
[+/–100]
Tap1 Delay
Tap2 Delay
Tap3 Delay
Tap4 Delay
Tap5 Delay
Tap6 Delay
Panning Preset
Source
Selects the modulation source of Tap1 feedback
amount and effect balance.
Amount
Sets the Tap1 feedback amount and modulation
amount.
LFO
Frequency [Hz]
This sets the LFO speed, in Hz.
LFO Type
This controls whether the effect uses its individual
LFO, or one of the Common FX LFOs. For more
information, see "LFO Type" on page 777.
Common LFO Phase Ofs [deg]
When Type is set to Common FX LFO 1 or 2, this lets
you offset the phase from the master LFO.
OUTPUT
This is the standard effects output section, with
modulatable control over wet/dry balance. For more
information, see "OUTPUT" on page 764.
Tap 5 = 120 degrees
Tap 6 = 300 degrees
Tap 1...6 [msec]
This sets the tap's delay time.
Depth 1...6
Wet / Dry This sets the tap's chorus depth.
Status 1...6
This turns the tap on or off, or allows its output level to
be modulated by the selected Dmod source.
Wet / Dry
Always On: Output is always on. (No modulation)
Always Off: Output is always off. (No modulation)
On→Off (Dmod): Output level fades from on to off via
the modulation source.
Off→On (Dmod): Output level fades from off to on via
the modulation source.
Combining these parameters, you can change from 4-
phase chorus to two-tap delay by crossfading them
gradually via the modulation source during a
performance.
Tap 1 Feedback
Tap1 Feedback
Sets the amount of feedback from Tap1.
[Off...Tempo]
[0.02...13.00]
[Individual, Common1, Common2]
[–180...+180]
[Always On, Always Off,
On➝Off (Dmod), Off➝On (Dmod)]
[+/–100]
[0...2000]
[0...30]
[+/–100]