Korg Electronic Keyboard Parameter Manual page 711

Note: The CD-R/RW Drive Audio Input settings are
linked with the Sampling mode "5–1b: CD-R/RW
Drive Audio Input" settings.
LEFT
RIGHT
Bus Select (IFX/Indiv.)
[L/R, IFX1...12, 1...8, 1/2...7/8, Off]
L/R: The audio signal from the CD-R/RW drive will be
sent to the L/R bus. Normally you will use the L/R
setting. The signal can be monitored from the L/R
outputs and from headphones.
IFX1...12: The audio signal from the CD-R/RW drive
will be sent to the IFX1–12 bus. Choose this setting if
you want to apply an insert effect.
1...8: The audio signal from the CD-R/RW drive will
be sent in monaural to INDIVIDUAL 1, 2, 3, 4, 5, 6, 7,
or 8.
1/2...7/8: The audio signal from the CD-R/RW drive
will be sent via the Pan settings to INDIVIDUAL 1 and
2, 3 and 4, 5 and 6, or 7 and 8 in stereo.
Off: The audio signal from the CD-R/RW drive will
not be input.
FX Ctrl Bus (FX Control Bus)
This sends the audio signal from the CD-R/RW drive
to the FX Control buses (two stereo channels; FX Ctrl1,
2).
REC Bus
This sends the audio signal from the CD-R/RW drive
to the REC buses (four mono channels 1, 2, 3, 4).
Off: The audio signal will not be sent to the REC bus.
Normally you will use the Off setting.
1, 2, 3, 4: The audio signal from the CD-R/RW drive
will be sent to the corresponding REC bus. The Pan
setting will be ignored, and the signal will be sent in
monaural.
1/2, 3/4: The audio signal from the CD-R/RW drive
will be sent to the corresponding REC buses. The
signal will be sent via the Pan setting to buses 1 and 2
or 3 and 4 in stereo.
Send1 (to MFX1)
Send2 (to MFX2)
These specify the level at which the audio signal from
the CD-R/RW drive is sent to the master effects.
Send1 (to MFX1): Send the signal to master effect 1.
Send2 (to MFX2): Send the signal to master effect 2.
These settings are ignored if Bus Select is other than
L/R or off.
If Bus Select (IFX/Indiv.) is set to IFX1–12, the send
levels to the master effects are set by the post-IFX1–12
Send1 and "Send2."
Pan
This specifies the panning of the audio signal from the
CD-R/RW drive. Normally you will set Left and Right
to L000 and R127 respectively.
[Off, 1, 2]
[Off, 1, 2, 3, 4, 1/2, 3/4]
[000...127]
[000...127]
[L000...C064...R127]
Disk P1: Audio CD
Level
This specifies the level of the audio signal sent from the
CD-R/RW drive. Normally you will set this to 127.
To summarize, the normal settings are as follows.
LEFT: Bus Select (IFX/Indiv.) L/R, REC Bus Off, FX
Ctrl Bus Off, Send1 000, Send2 000, Level 127, Pan
L000
RIGHT: Bus Select (IFX/Indiv.) L/R, REC Bus Off, FX
Ctrl Bus Off, Send1 000, Send2 000, Level 127, Pan
R127
1–2: Play Audio CD
[000...127]
701