139: Phaser - Chorus/Flanger - Korg Electronic Keyboard Parameter Manual

Tap2 Time [msec]
Sets the Tap2 delay time.
Tap1 Level
Sets the Tap1 output level. p.832.
Feedback
Sets the Tap2 feedback amount.
High Damp [%]
Sets the damping amount in the high range. p.829.
Wet/Dry
Sets the multitap delay effect balance.

139: Phaser - Chorus/Flanger

This effect combines a mono phaser and a
chorus/flanger.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Phaser
+
Phaser
EQ
LEQ HEQ
Trim
Phaser
Resonance
Wet / Dry
Right
LFO: Tri / Sine
LFO: Tri / Sine
PHASER
LFO
Waveform
Selects the LFO Waveform.
Frequency [Hz]
Sets the LFO speed.
PHASER
Manual
Sets the frequency to which the effect is applied.
Depth
Sets the depth of LFO modulation.
Resonance
Sets the resonance amount. p.805.
Wet/Dry
Sets the phaser effect balance. p.780, p.806.
CHORUS/FLANGER
Pre EQ
Trim
Sets the EQ input level.
LEQ Gain [dB]
Sets the gain of the Low EQ.
[0.0...1360.0]
[0...100]
[+/–100]
[0...100]
[Dry, 1:99...99:1, Wet]
Wet / Dry
Chorus/Flanger
Chorus/Flanger
Normal
+
Output Mode
—
Wet Invert
Feedback
Cho/Flng
Wet / Dry
Wet / Dry
[Triangle, Sine]
[0.02...20.00]
[0...100]
[0...100]
[+/–100]
[Dry, 1:99...99:1, Wet]
[0...100]
[–15...+15]
Mono-Mono Serial 139: Phaser - Chorus/Flanger
Source
Selects the Wet/Dry modulation source for the
multitap delay.
Amount
Sets the Wet/Dry modulation amount for the multitap
delay.
OUTPUT
This is the standard effects output section, with
modulatable control over wet/dry balance. For more
information, see "OUTPUT" on page 764.
HEQ Gain [dB]
Sets the gain of the High EQ.
LFO
Frequency [Hz]
Sets the LFO speed.
Waveform
Selects the LFO Waveform.
FLANGER
Delay Time [msec]
Sets the delay time.
Depth
Sets the depth of LFO modulation.
Feedback
Sets the feedback amount. p.803.
Output Mode
Selects whether the chorus/flanger output is mono or
pseudo-stereo. For more information, see "Output
Mode" on page 857.
Wet/Dry
Sets the effect balance of the chorus/flanger. See
"Wet/Dry" on page 780, and "Feedback" on page 803.
Source
Selects the Wet/Dry modulation source for the
chorus/flanger.
Amount
Sets the Wet/Dry modulation amount for the
chorus/flanger.
OUTPUT
This is the standard effects output section, with
modulatable control over wet/dry balance. For more
information, see "OUTPUT" on page 764.
[Off...Tempo]
[+/–100]
[–15...+15]
[0.02...20.00]
[Triangle, Sine]
[0.0...1350.0]
[0...100]
[+/–100]
[Normal, Wet Invert]
[Dry, 1:99...99:1, Wet]
[Off...Tempo]
[+/–100]
875