Table of Contents
Advertisement
number of events is then performed in each Phase,
regardless of any other circumstances which might
trigger a Phase Change. When the Phase "Length
Mode" is 0: AC-Actual, then these parameters are not
available. The Phases will then change according to the
movement through the Note Series.
0: AC-Actual not available when GE Type (☞p.897)
= 1: Generated-Gated.
Beginning Offset %
End Offset %
Sets an overall beginning and end range in the Note
Series for note generation within the Phase. Even
though settings in the Note Series Group may have
End Loop Parameters
Determines whether a portion of the effect will loop,
after a certain number of steps of the Phase Pattern
have been completed. Note that once the loop has
started, it continues using the Phase Pattern, and
current Phase "Length Mode".
End Loop On/Off
0: Off
1: On
Enables/disables this feature, and the following two
parameters.
End Loop Start Step
Selects a total number of Phase Pattern steps to
complete before entering the End Loop. For example, if
the Phase Pattern was set to a 2 step pattern of {1, 2}
Pattern Parameters
Pattern Items
Sets the number of steps in the Phase Pattern.
Pattern Step1...16
0: Phase1
1: Phase2
Sets which phase (Phase 1 or Phase 2) will be used for
generating data when a specific step of the Phase
Pattern is entered during playback. For each step that
is enabled, the step may be set to either Phase 1 or
Phase 2.
Note: If the number of steps in the Phase Pattern
(Pattern Items) is less than the step being edited, this
will produce no audible results.
Template Parameters
Selects one of 16 templates (each having 4 steps) that
can be applied to all or parts of the Phase Pattern. They
specify 16 different combinations of Phase 1 and Phase
2 within a 4 step section:
0: 1-1-1-1
6: 1-2-1-1
1: 2-2-2-2
7: 2-1-1-1
2: 1-2-1-2
8: 1-1-2-2
3: 2-1-2-1
9: 1-2-2-1
4: 1-1-1-2
10: 2-2-1-1
created a very long Note Series, these can be used to
select just a portion of the Note Series from which to
generate notes over the length of a particular Phase.
For example, if the "Beginning Offset" is 25% and the
"End Offset" is 75%, note generation within the Phase
would be restricted to coming from the portion of the
Note Series 1/4 to 3/4 of the way from the beginning.
[0...100 (%)]
[0...100 (%)]
and the Start Step menu to 4, the loop would be
entered after the 2nd time through the Phase Pattern,
at the end of the 4th step in total. Not available if the
"End Loop On/Off" is set to 0: Off.
End Loop Length
[0, 1]
Determines how many events (notes or clusters) will
be moved forward/backward while looping,
according to various other parameters such as the
Index Pattern. Not available if the "End Loop On/Off"
[1...17]
is set to 0: Off.
[1...16 (steps)]
Template (All Steps)
[0, 1]
The chosen template is applied to all steps of the Phase
Pattern, regardless of how many there are. For
example, if you selected 6: 1-2-1-1 (Template 6), then
the following would happen to the Phase Pattern:
If the Phase Pattern had 1 steps:
If the Phase Pattern had 2 steps:
If the Phase Pattern had 4 steps:
If the Phase Pattern had 7 steps:
If the Phase Pattern had 16 steps: 1-2-1-1 1-2-1-1 1-2-1-1 1-2-1-1
Template Steps 1...4
Applies the selected template only to the first 4 steps of
[0...15]
the Phase Pattern.
If there are more steps, they will remain unchanged.
Template Steps 5...8
Applies the selected template only to steps 5-8 of the
12: 1-2-2-2
Phase Pattern. If there are more steps, they will remain
unchanged. Steps 1–4 will remain unchanged.
13: 2-2-2-1
14: 2-2-1-2
Template Steps 9...12
15: 2-1-2-2
Same as above, except for steps 9–12.
Phase Group
Not available when "GE Type" (☞p.897) = 1:
Generated-Gated, unless "Gate Type" (☞p.897) = 1:
Vel CP. If 2: Generated-Drum, the Note Series can
be applied as pitch bend, discussed elsewhere.
1...96: events
5: 1-1-2-1
11: 2-1-1-2
End Loop Parameters
[1...96]
1
1-2
1-2-1-1
1-2-1-1 1-2-1
907
Advertisement
Table of Contents
