086: Multiband Mod. Delay - Korg Electronic Keyboard Parameter Manual

Effect Guide

086: Multiband Mod. Delay

This effect divides the input signal into low, mid, and
high-frequency bands, and applies a modulation delay
to each band.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Feedback
Input Source
LFO
LFO
+
LFO
LFO
Right
Dmod
Input Level [%]
Sets the modulation amount of the input level. p.820.
Src (Source)
Selects the modulation source for the input level. p.820.
Feedback Src (Source)
Selects the modulation source of feedback amount.
Output Level Src ( Source)
Selects the modulation source for the output level.
XOVER FILTER
1-2 [Hz]
Sets the frequency at which bands 1 and 2 are divided.
2-3 [Hz]
Sets the frequency at which bands 2 and 3 are divided.
3-4 [Hz]
Sets the frequency at which bands 3 and 4 are divided.
BAND1 DELAY
Input
Selects the input for band 1: either the signal from the
crossover, or the direct signal.
Feedback Src (Source)
Selects the feedback source for band 1. This lets you
connect the feedback of each band to other bands.
Time [msec]
Sets the delay time for the band 1.
Pan
Sets the panning for band 1.
Feedback
Sets the feedback amount for band 1.
836
Feedback Source
Level Pan
High Damp Low Damp
Delay
Feedback Source
Delay
Feedback Source
Delay
Feedback Source
Delay
[+/–100]
[Off...Tempo]
[Off...Tempo]
[Off...Tempo]
[20...20.00k]
[20...20.00k]
[20...20.00k]
[Xover, Direct]
[Band1, Band2, Band3,
[0.0...1200.0]
[L, 1...99, R]
[+/–100]
Amt (Feedback Amount)
Sets the amount of modulation for the band 1
feedback.
Low Damp [%]
Wet / Dry Sets the amount of low-frequency attenuation for band
1.
High Damp [%]
Sets the amount of high-frequency attenuation for
band 1.
Output Level
Sets the output level for band 1.
Wet / Dry
Amt (Output Level Amount)
Sets the amount of modulation for the band 1 output
level.
BAND2 DELAY
Band 2 has the same parameters as the "BAND1
DELAY," above.
BAND3 DELAY
Band 3 has the same parameters as the "BAND1
DELAY," above.
BAND4 DELAY
Band 4 has the same parameters as the "BAND1
DELAY," above.
BAND1 LFO
Frequency [Hz]
Sets the LFO speed for band 1.
Depth
Sets the LFO modulation depth for band 1.
Type
Selects LFO, Common FX LFO1, or Common LFO2 for
band 1. p.777.
Cmn LFO [deg] (Common LFO Phase Offset
[degrees])
Sets the phase offset when Type = Common 1 or
Band4]
Common 2. p.777.
BAND2 LFO
Band 2's LFO has the same parameters as the "BAND1
LFO," above.
BAND3 LFO
Band 3's LFO has the same parameters as the "BAND1
LFO," above.
[+/–100]
[0...100]
[0...100]
[0...100]
[+/–100]
[0.02...20.00]
[0...187]
[Indiv., Cmn1, Cmn2]
[–180...+180]