Table of Contents
Advertisement
Module ID
Indicates which parameters you are controlling from
the KARMA SLIDERS or KARMA SWITCHES.
A, B, C, D: Indicates the KARMA Module that is being
controlled. In this case, you are controlling a GE Real-
Time Parameter.
P: Indicates that the slider or switch is controlling a
Performance Real-Time Parameter.
Parameter No.
When "Module ID" is A,B,C or D (KARMA Module),
this area indicates the GE Real-Time Parameter
number 01–32 that you are controlling (displayed in
pages 7–5: GE Real-Time Parameters). If "Module ID"
is P, this area indicates the Performance Real-Time
Parameter number 01–08 (displayed in pages 7–6:
Performance Real-Time Parameters) that you are
controlling.
Parameter Value
This area indicates the value of the GE Real-Time
Parameter or Performance Real-Time Parameter you
are controlling. The value will change as you move the
slider or operate the switch.
A slider or switch can have multiple parameters
assigned to it. A maximum of four assigned
parameters can be displayed here in the available
space. If there are more, they will not be displayed
(but a ">" will be added to the end of the line). They
will still function when the control is activated, but
you cannot view their values directly.
0–6c: Note/CC Activity
A (Module A)
CCs/Notes
This is a real-time display of the notes or CC# message
generated by the KARMA Modules (Module [A], [B],
[C], [D]).
Scan Zone
The key zone settings of the KARMA Module are
displayed as a solid blue line under the notes display.
For more information, see "Bottom (Key Zone
Bottom)" on page 376.
B, C, D (Modules B, C, D)
This area shows the CCs/Notes and Scan Zone for
Modules B through D. These settings are the same as
for "A (Module A)," above.
0–6d: Realtime Controls
This displays the names and settings of KARMA
SLIDERS 1–8 and KARMA SWITCHES 1–8.
1...8
The current setting of the KARMA SWITCH or
KARMA SLIDER is shown here, which is linked with
the operation of the front panel switch or slider.
[A, B, C, D, P]
Then, you could get rid of the section that says:2-8 are
the same as 1 etc.
KARMA SWITCH 1
The current setting of KARMA SWITCH 1 is shown
here. This is linked with the operation of switch 1. You
can also operate this by touching the switch shown in
the display.
KARMA SWITCH 1 Stored Value
[01...32]
This indicates the setting of KARMA SWITCH 1 that is
written into the program.
KARMA SWITCH 1 Control Timbre Category Name
This indicates the category of the program used by the
timbre that is being played from the KARMA Module.
This will indicate Multi if a single KARMA Module is
playing multiple timbres of differing categories.
KARMA SWITCH 1 Name
This indicates the name of KARMA SWITCH 1.
You can assign this name in Combination 7–9:
Name/Map.
KARMA SLIDER 1
This indicates the current setting of KARMA SLIDER
1. This is linked with the operation of slider 1. You can
also operate this by touching the slider head and
adjusting the value with the Value Slider, the
Up/Down Keys, the data Wheel, etc.
KARMA SLIDER 1 Stored Value
This indicates the setting of slider 1 that is written into
the program.
KARMA SLIDER 1 Control
Timbre Category Name
This indicates the category of the program used by the
timbre that is being played from the KARMA Module.
This will indicate Multi if a single KARMA Module is
playing multiple timbres of differing categories.
KARMA SLIDER 1 Name
This indicates the name of KARMA SLIDER1.
You can assign this name in Combination 7–9:
Name/Map.
▼ 0–6: Page Menu Commands
The number before each command shows its ENTER +
number-key shortcut. For more information on these
shortcuts, see "ENTER + 0-9: shortcuts for menu
commands" on page 138.
• 0: Write Combination. For more information, see
"Write Combination" on page 405.
• 1: Exclusive Solo. For more information, see
"Exclusive Solo" on page 138.
• 2: Copy From Program. For more information, see
"Copy From Program" on page 405.
• 3: Copy KARMA Module. For more information,
see "Copy KARMA Module" on page 408.
Combination P0: Play
0–6: KARMA GE
329
Advertisement
Table of Contents
