Table of Contents
Advertisement
4–2a: EXi 1
Input Source
[Off, Audio Input 1/2...3/4,
S/P DIF Input L/R, L/R Output,
Indiv. Output 1/2...7/8, REC 1/2, 3/4,
FX Control 1, 2, IFX 1...12, MFX 1, 2, TFX 1, 2]
This selects the input source for EXi1. You can use this
to create a feedback loop, if desired.
Off disables the input.
Audio Input 1/2...3/4 and S/P DIF Input L/R use the
live audio from the selected input.
L/R Output and Indiv. Output 1/2...7/8 use the audio
as it is heard from the selected output (like connecting
a cable from the output back to the input).
4–5: Vector Control
Vector Synthesis lets you control Program and Effects
parameters by moving the Vector Joystick, by using the
programmable Vector Envelope, or by the combination
of the two.
This page works exactly like the similar page for HD-1
Programs, substituting EXi 1/2 for OSC 1/2. For more
information, see "1–5: Vector Control" on page 38.
4–6: Vector Envelope
The Vector Envelope works together with the Vector
Joystick to control the Vector position. It's also special
because it's the only programmable modulation source
which lets you modulate both Program and Effects
parameters.
The Vector Envelope is different from the other
envelopes in several ways:
• Each point has two "levels" - one for the X axis, and
one for the Y axis.
• The envelope times can be based on seconds and
milliseconds, or synced to tempo.
• Each point has a hold time, as well as a transition
time to the next point.
• The envelope can loop between two points, for
either a specified number of repeats, or as long as
you hold the note.
4–8: Set Up Controllers
This page lets you set up the functionality of SW1/2
and Real-Time Knobs 5–8. It works exactly like the
similar page for HD-1 Programs; for more information,
see "1–8: Set Up Controllers" on page 45.
EXi Program P4: Basic/Vector
REC 1/2...3/4 and FX Control 1, 2 use the audio from
the selected bus.
IFX 1...12, MFX 1, 2, and TFX 1, 2 use the output of the
selected effect.
Channel Select
Stereo/L+R: This selection routes a stereo signal to EXi
with stereo inputs, and an L+R summation to EXi with
mono inputs.
Left, Right: This uses only a mono signal from the
selected channel.
4–2b: EXi 2
EXi 2 has the same controls as EXi 1, above.
▼ 4–5: Page Menu Commands
The number before each command shows its ENTER +
number-key shortcut. For more information on these
shortcuts, see "ENTER + 0-9: shortcuts for menu
commands" on page 138.
• 0: Write Program. For more information, see "Write
Program" on page 138.
• 1: Exclusive Solo. For more information, see
"Exclusive Solo" on page 138.
• 2: Copy EXi Oscillator. For more information, see
"Copy EXi Oscillator" on page 169.
This page works exactly like the similar page for HD-1
Programs, substituting EXi 1/2 for OSC 1/2. For more
information, see "1–6: Vector Envelope" on page 42.
▼ 4–6: Page Menu Commands
The number before each command shows its ENTER +
number-key shortcut. For more information on these
shortcuts, see "ENTER + 0-9: shortcuts for menu
commands" on page 138.
• 0: Write Program. For more information, see "Write
Program" on page 138.
• 1: Exclusive Solo. For more information, see
"Exclusive Solo" on page 138.
• 2: Copy EXi Oscillator. For more information, see
"Copy EXi Oscillator" on page 169.
▼ 4–8: Page Menu Commands
The number before each command shows its ENTER +
number-key shortcut. For more information on these
shortcuts, see "ENTER + 0-9: shortcuts for menu
commands" on page 138.
4–5: Vector Control
[Stereo/L+R, Left, Right]
163
Advertisement
Table of Contents
