045: Bi Chorus - Korg Electronic Keyboard Parameter Manual

Source
This selects a modulation source to modulate the tap
output levels (as set by Status, above) and the Tap 1
Feedback amount.
Amount
Sets the modulation amount for the Tap 1 Feedback.
Panning Preset [1: L 1 2 3 4 5 6 R, 2: L 135 246 R,
3: L 1 3 5 2 4 6 R, 4: L 1 4 5 6 3 2 R]
This selects combinations of stereo panning patterns
for the tap outputs.

045: Bi Chorus

This effect lets you place two independent
chorus/flanger units in series or in parallel. If placed in
series, feedback can be applied to the sound that has
passed through the two chorus modules, creating even
more complex modulation.
Wet: Mono In - Stereo Out / Dry: Stereo In -Stereo Out
Left
Feedback
+
Dual
Mode
Serial
LFO1
Phase Lock
LFO2
Feedback
Right
CHORUS1
Manual
Sets the delay time for chorus 1.
LFO1 Depth
Sets the LFO modulation depth for chorus 1.
Source
Selects the modulation source that will control LFO
modulation depth.
Amount
Sets the amount by which the chorus 1 LFO
modulation depth will be controlled.
Feedback
Sets the feedback amount for chorus 1.
CHORUS2
Manual
Sets the delay time for chorus 2.
LFO2 Depth
Sets the LFO modulation depth for chorus 2.
Amount
Sets the amount by which the chorus 2 LFO
modulation depth will be controlled.
[Off...Tempo]
[+/–100]
Wet / Dry
Output Level1
Chorus
+
Output Mode
Chorus
Output Level2
Wet / Dry
[0...100]
[0...100]
[Off...Tempo]
[+/–100]
[0...100]
[0...100]
[0...100]
[+/–100]
Chorus, Flanger, and Phaser
LFO
Frequency [Hz]
This sets the LFO speed, in Hz.
OUTPUT
This is the standard effects output section, with
modulatable control over wet/dry balance. For more
information, see "OUTPUT" on page 764.
Feedback
Sets the feedback amount for chorus 2. When Routing
is set to Serial, this feeds back into Chorus 1, and
Chorus 1's own Feedback setting is ignored.
LFO1/2
LFO1/2 Lock
Lock-Common1, Lock-Common2]
This selects the LFO(s) used by the two choruses.
Unlock: LFO 1 and LFO 2 will operate independently.
Lock-LFO 1: both choruses will use LFO 1, with an
optional phase offset for LFO 2 (see "LFO2 Phase
[degrees]," below).
Lock-Common 1 or Lock Common 2: both choruses
will use the selected FX Common LFO, with an
optional phase offset for LFO 2.
LFO 1/2 Lock: Unlock
LFO1 Chorus1
LFO2 Chorus2
LFO 1/2 Lock: Lock - Common1
Common FX LFO1 Chorus1
LFO2 Phase Chorus2
LFO2 Phase [degrees]
Sets the phase difference between LFO1 and LFO2,
when LFO 1/2 Lock is set to anything other than
Unlock.
LFO1 Frequency [Hz]
Sets the LFO 1 speed. This applies only if LFO 1/2 Lock
is set to Unlock or Lock-LFO1.
LFO2 Frequency [Hz]
Sets the LFO 2 speed. This applies only if LFO 1/2 Lock
is set to Unlock.
Source
Selects a source to modulate the speeds of LFO1 & 2.
LFO1 Amount
This sets the LFO1 Frequency modulation amount, in
Hz.
045: Bi Chorus
[0.02...13.00]
[0...100]
[Unlock, Lock-LFO1,
LFO 1/2 Lock / LFO2 Phase
LFO 1/2 Lock: Lock - LFO1
LFO1 Chorus1
LFO2 Phase Chorus2
LFO 1/2 Lock: Lock - Common2
Common FX LFO2 Chorus1
LFO2 Phase Chorus2
[–180...+180]
[0.02...20.00]
[0.02...20.00]
[Off...Tempo]
[–20.00...+20.00]
801