083: Stereo Dynamic Delay - Korg Electronic Keyboard Parameter Manual

MOD DELAY
L Delay Time [msec]
Sets the delay time for the left channel.
R Delay Time [msec]
Sets the delay time for the right channel.
L Depth
Sets the depth of the left LFO modulation.
R Depth
Sets the depth of the right LFO modulation.
L Feedback
Sets the feedback amount of left delay.
R Feedback
Sets the feedback amount of right delay.
OUTPUT
This is the standard effects output section, with
modulatable control over wet/dry balance. For more
information, see "OUTPUT" on page 764.

083: Stereo Dynamic Delay

This stereo delay controls the level of delay according
to the input signal level. You can use this as a ducking
delay that applies delay to the sound only when you
play keys at a high velocity or only when the volume
level is low.
Stereo In - Stereo Out
Left
High Damp Low Damp
Delay
Feedback
High Damp Low Damp
Delay
Right
FB
+
Attack, Release
Envelope
Threshold
CONTROL
Target [None, Output Level, Feedback]
Selects the modulation target for the input signal.
Polarity
Reverses level control. p.833.
Offset
Sets the offset of level control. p.833.
Threshold
Sets the level to which the effect is applied. p.833.
Attack
Sets the attack time of level control. p.834.
Release
Sets the release time of level control. p.834.
CONTROL: Dmod Modulation
When the modulation source is used for control, this
parameter reverses the left and right modulation
[0.0...1000.0]
direction.
LFO: L LFO Phase [degrees], R LFO Phase [degrees],
[0.0...1000.0]
Dmod Sync, and Source
If Dmod Sync is On, the LFO will be reset by the
modulation source that is received.
[0...200]
The Source parameter sets the modulation source that
resets the LFO. For example, you can assign Gate as a
[0...200]
modulation source so that the sweep always starts
from the specified point.
L LFO Phase and R LFO Phase set the phase obtained
[+/–100]
when the left and right LFOs are reset. In this way, you
can create changes in pitch sweep for the left and right
channels individually.
[+/–100]
DELAY
L Delay Time [msec]
Sets the delay time for the left channel.
R Delay Time [msec]
Sets the delay time for the right channel.
Wet / Dry
Feedback
Spread
Sets the feedback amount.
High Damp [%]
Wet / Dry
Sets the damping amount in the high range. p.829.
Out
Control Target
Low Damp [%]
Sets the damping amount in the low range. p.829.
Spread
Sets the width of the stereo image of the effect sound.
p.829.
[+, –]
OUTPUT
This is the standard effects output section, with
[0...100]
modulatable control over wet/dry balance. For more
information, see "OUTPUT" on page 764.
[0...100]
CONTROL: Polarity, Offset, and Threshold
The "Offset" parameter specifies the value for the
"Target" parameter (that is set to None), expressed as
[1...100]
the ratio relative to the parameter value (the
"Wet/Dry" value with "Target"=Output level, or the
"Feedback" value with "Target"=Feedback).
[1...100]
Delay 083: Stereo Dynamic Delay
The effect is off when a value of the modulation
source specified in the Source parameter is 63 or
smaller, and the effect is on when the value is 64 or
higher. The LFO is triggered and reset to the "L LFO
Phase" and "R LFO Phase" settings when the value
changes from 63 or smaller to 64 or higher.
[0.0...1360.0]
[0.0...1360.0]
[+/–100]
[0...100]
[0...100]
[+/–100]
833