Table of Contents
Advertisement
MIDI transmission when the OASYS's controllers are operated
VJS
CC# MIDI messages
110 PAD1 trigger velocity
*
111 PAD2 trigger velocity
*
112 PAD3 trigger velocity
*
113 PAD4 trigger velocity
*
114 PAD5 trigger velocity
*
115 PAD6 trigger velocity
*
116 PAD7 trigger velocity
*
117 PAD8 trigger velocity
*
118 Vector joystick X
[*](X) *
119 Vector joystick Y
[*](Y) *
Universal exclusive
Master volume
Master balance
Master fine tune
Master coarse tune
(1): When a KARMA controller is assigned to a CC#
indicated by [*] (Global P2– Controller)
#: Fixed
*: Assignable
[*]: The vector joystick, KARMA realtime controls, and
chord trigger controllers can be assigned to CC#00–
119. CC#s indicated by [*] will be assigned
automatically when you execute the Global P2–
Controller page menu command "Reset Controller
MIDI Assign" with the CC Default setting.
The CC Default settings are the CC#s recommended as
the CC# for each of these controllers. Normally you
should use these settings when assigning CC#s.
Fixed assignments
The following physical controls have fixed
assignments to MIDI CCs:
Joystick +Y
Modulation 1 (CC#1)
Joystick -Y
Modulation 2 (CC#2)
Joystick X
Pitch Bend
Value Slider
CC#18
Realtime Knob 1
Filter cutoff frequency (CC#74)
Realtime Knob 2
Filter resonance (CC#71)
Realtime Knob 3
Filter EG intensity (CC#79)
Realtime Knob 4
Release time (CC#72)
SW1
SW1 modulation On/Off (CC#80)
SW2
SW2 modulation On/Off (CC#81)
Ribbon Controller
Ribbon controller (CC#16)
Damper pedal
Damper (CC#64)
Program mode
When one of the OASYS's controllers is operated, a
control change message will be transmitted on the
global MIDI channel (MIDI Channel Global 1–1a).
If the Status (Sequencer 2–1a) of the track selected by
Track Select is EXT, EX2, or BTH, a control change
message will be transmitted on the MIDI channel
KARMA
VJS-CC
Realtime
On/
Control
Knob 5–8
Latch Scene
Off
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Pads
SW
Sliders
1–8
1–8
1–8
*
*
*
[*]PAD1
*
*
*
[*]PAD2
*
*
*
[*]PAD3
*
*
*
[*]PAD4
*
*
*
[*]PAD5
*
*
*
[*]PAD6
*
*
*
[*]PAD7
*
*
*
[*]PAD8
*
*
*
*
*
*
*
*
f the REALTIME KNOBS 1–8 or the assignable
pedal has been set to Master Volume, the universal
system exclusive message Master Volume will be
transmitted.
Combination mode
When one of the OASYS's controllers is operated, a
control change message will be transmitted on the
global MIDI channel (MIDI Channel Global 1–1a).
Simultaneously, the message will also be transmitted
on the MIDI channel (MIDI Channel Combination 2–
1a) of any timbre whose Status (Combination 0–1b, 2–
1a) is EXT or EX2.
When one of the OASYS's controllers is operated, its
effect will apply to any timbre whose Status is INT and
whose MIDI Channel setting is either Gch or the same
as the global MIDI channel.
In the case of Master Volume, the universal
exclusive message Master Volume will be
transmitted only on the global MIDI channel.
You can make settings for MIDI Filter (Combination
P3) to enable or disable control changes and
controllers for each timbre. When checked, the
above operations will be enabled.
Effect dynamic modulation can be controlled when the
Ch (Combination 8–7a, 9–2a, 9–3, 9–4, 9–5) setting for
IFX1–12, MFX1, 2, or TFX 1, 2 is either set to Gch or to
the same channel as the global MIDI channel. (In the
case of All Routed, control is possible on the MIDI
channel of any routed timbre.)
KARMA modules A, B, C, and D can be controlled if
the Input Channel and Output Channel (Combination
7–1c) settings specified for each module are Gch or
match the global channel.
Sequencer mode
When one of the OASYS's controllers is operated, its
effect will apply to the MIDI track 1–16 that is selected
by Track Select (Sequencer 0–1a).
specified by MIDI Channel (Sequencer 2–1a).
Dynamic MIDI Destinations
Foot
Foot
Available
Available
Switch
Pedal
for AMS
for Dmod
*
993
Advertisement
Table of Contents
