Korg Electronic Keyboard Parameter Manual page 632

Sampling mode
2) Press the OK button to execute Auto Sampling
Setup (Auto Resample through IFX), or press the
Cancel button if you decide not to execute. For more
information, please see "Auto Sampling Setup:
Automatically-set parameters and their values" on
page 622.
Note: When you are ready to resample (after executing
Auto Resample through IFX), perform the following
steps.
1) Use Key (0–8c) to specify the key to which the
sample you want to resample is assigned.
2) Use P8: Insert Effect to make effect settings. To
hear the sound, play the note you specified in Key.
Auto Sampling Setup: Automatically-set parameters and their values
*1
Input (Input Source)
Input1, 3, S/P DIF-L
Input2, 4, S/P DIF-R
Sampling Setup
(Name)
REC Sample Setup
Select Directly
Routing
Insert FX
–: Not set automatically
[ ]: Set automatically according to the parameter
settings in the dialog box
*1Edit sampling mode parameters
*2Uses the input source specified as Source Audio.
*3:If IFX is Off this will be L/R. If IFX1...12 is
selected this will be IFX1...12.
622
Input1, 2, 3, 4
S/P DIF
Bus Select
FX Ctrl Bus
REC Bus
Send1/2
Pan
Level
Bus Select
FX Ctrl Bus
REC Bus
Send1/2
Pan
Level
Source Bus
Source Direct Solo
Trigger Sampling START SW
Metronome Precount
Pre Trigger REC
Resample
Save to
Mode
Rec Level
Auto +12dB On
Auto Loop On
–
Bus Select (All OSCs to)
FX Crtl Bus
REC Bus
Send1/2
Bus Select (Post IFX)
3) To begin resampling, press the SAMPLING REC
key and then the SAMPLING START/STOP switch.
(This is because Trigger is set to Sampling START
SW.) The sample will play, and when playback ends,
it will be resampled.
Note: To check the resampled data, play the note you
specified in the Key parameter.
To prevent the insert effect from being applied "in
duplicate" when you listen to the resampled data,
"Bus Select All OSCs to" (8–1b) will automatically
be set to L/R when resampling ends. If you want to
apply IFX and resample once again, you will need
to change this setting back to the same IFX.
[Initialize] [REC Audio Input]
[Source Audio]
Off [IFX]
Off Off
Off Off
000 000
L000 L000
127 127
Off [IFX]
Off Off
Off Off
000 000
R127 R127
127 127
L/R L/R
(N/A) (N/A)
Sampling START SW
(N/A) (N/A)
–
Manual Manual
RAM [Save to]
Stereo [Source Audio]
+0.0 +0.0
On On
On
–
L/R
Off
Off
127
– L/R
*4L-Mono if the Source Audio is Mono-L, R-Mono if
it is Mono-R, and Stereo if it is Stereo
*5When Save to=RAM
*6Specify the BUS Select of that IFX1...12. If effects
are chained, specify the last IFX in the chain.
[Auto Resampling through IFX]
Input1, 2, 3, 4
*2
S/P DIF
*3
Off
Off
Off
000
L000
127
*3
Off
Off
Off
000
R127
127
L/R
(N/A)
Sampling START SW
(N/A)
– –
Auto
RAM
*4
Stereo
+0.0
*5
On
– –
– –
– [IFX]
– Off
– Off
– 000
*6
L/R
*6