082: Stereo Modulation Delay - Korg Electronic Keyboard Parameter Manual

Effect Guide
Tap2 Time [msec]
Sets the Tap2 delay time.
Feedback (Tap2)
Sets the Tap2 feedback amount.
Source
Selects the modulation source of the Tap2 feedback
amount.
Amount
Sets the modulation amount of the Tap2 feedback
amount.
Tap1 Level
This lets you adjust the relative volume of Tap1,
compared to Tap2 (which is always at the maximum
volume). Setting a lower volume for Tap1 can help to
create interesting accent patterns.
High Damp [%]
Sets the damping amount in the high range. p.829.

082: Stereo Modulation Delay

This stereo delay uses an LFO to sweep the delay time.
The pitch also varies, creating a delay sound which
swells and shimmers. You can also control the delay
time using a modulation source.
Stereo In - Stereo Out
Left
Right
D -mod
Response
LFO: Tri / Sine
LFO Sync
CONTROL
Modulation Mode
Switches between LFO modulation control and
modulation source control.
Dmod Modulation
Reversed L/R control by modulation source. p.833.
Source
Selects the modulation source that controls delay time.
Response
Sets the rate of response to the modulation source.
LFO
Waveform
Selects the LFO Waveform.
Shape
Changes the curvature of the LFO Waveform. p.780.
832
[0.0...1360.0]
[+/–100]
[Off...Tempo]
[+/–100]
[0...100]
[0...100]
Delay
Feedback
Delay
D-mod
L/R: +/+ +/—
LFO Shape
LFO
LFO Phase Modulation Mode
[LFO, Dmod]
[L/R:+/+, L/R:+/–]
[Off...Tempo]
[0...30]
[Triangle, Sine]
[-100...+100]
Low Damp [%]
Sets the damping amount in the low range. p.829.
Spread
Sets the width of the stereo image of the effect sound.
p.829.
Source
Selects the modulation source of the effect sound's
stereo image width.
Amount
Sets the modulation amount of the effect sound's
stereo image width.
OUTPUT
This is the standard effects output section, with
modulatable control over wet/dry balance. For more
information, see "OUTPUT" on page 764.
L LFO Phase [degrees]
Sets the phase obtained when the left LFO is reset.
p.833.
R LFO Phase [degrees]
Sets the phase obtained when the right LFO is reset.
Wet / Dry
p.833.
Dmod Sync
Switches LFO reset off/on. p.833.
Source
Wet / Dry
Selects the modulation source that resets the LFO.
Frequency [Hz]
This sets the LFO speed, in Hz.
MIDI/Tempo Sync
BPM
Base Note
Times
When MIDI/Tempo Sync is on, the LFO speed is set by
BPM, Base Note, and Times, instead of Frequency. For
more information, see "MIDI/Tempo Sync" on
page 777.
Type
This controls whether the effect uses its individual
LFO, or one of the Common FX LFOs. For more
information, see "LFO Type" on page 777.
Common LFO Phase Offset [degrees]
When Type is set to Common FX LFO 1 or 2, this lets
you offset the phase from the master LFO.
[Off...Tempo]
[–180...+180]
[–180...+180]
[Check-box]
[Off...Tempo]
[0.02...20.00]
[Check-box]
[MIDI, 40.00...240.00]
[Individual, Common1, Common2]
[0...100]
[+/–100]
[+/–100]
[ ... ]
[x1...x32]
[+/–180]