H3: Analog Inputs - YASKAWA CIPR-CR70A Series Technical Manual

10 Parameter List
Setting Function
4F Braking Resistor
Overheat (rH)
51 Safe Torque OFF
52 Warning Signal
60 Internal Cooling
Fan Failure
62 Modbus Reg 1
Status Satisfied
63 Modbus Reg 2
Status Satisfied
66 Comparator1
67 Comparator2
69 External Power
24V Supply
6A Data Logger Error
B1 DC Injection
Braking at Start
B2 DC Injection
Braking at Stop
B3 Motor 3 Selection
100 to 1FF Inverse Output of 0
to FF
■

H3: Analog Inputs

No.
Name
(Hex.)
H3-01 Terminal A1 Signal
Level Select
(0410)
H3-02 Terminal A1
Function Selection
(0434)
468
V/f CL-V/f OLV CLV AOLV
The terminal activates when the braking resistor overheats and the drive detects an rH
[Braking Resistor Overheat] fault.
V/f CL-V/f OLV CLV AOLV
The terminal turns on (safety stop state) when the safety circuit and safety diagnosis
circuit is not experiencing a failure and when both terminals H1-HC and H2-HC are off
(released).
ON : Safety stop state
OFF : Safety circuit fault or RUN/READY
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the number of starts reaches the detection level.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the drive detects a cooling fan failure in the drive.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the bit specified by H2-08 [Modbus Register 1 Bit Select]
for the MEMOBUS register address set with H2-07 [Modbus Register 1 Address Select]
activates.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the bit specified by H2-10 [Modbus Register 2 Bit Select]
for the MEMOBUS register address set with H2-09 [Modbus Register 2 Address Select]
activates.
V/f CL-V/f OLV CLV AOLV
The monitor value set with H2-20 [Comparator 1 Monitor Selection] is on while in range
of the time set with H2-24 [Comparator 1 On-Delay Time] and the values of H2-21
[Comparator 1 Lower Limit] and H2-22 [Comparator 1 Upper Limit] are in range.
V/f CL-V/f OLV CLV AOLV
The monitor value set with H2-26 [Comparator 2 Monitor Selection] is on while in range
of the time set with H2-30 [Comparator 2 On-Delay Time] and the values of H2-27
[Comparator 2 Lower Limit] and H2-28 [Comparator 2 Upper Limit] are in range.
V/f CL-V/f OLV CLV AOLV
The terminal activates when there is an external 24V power supply between terminals
PS-AC.
ON : An external 24V power supply supplies power.
OFF : An external 24V power supply does not supply power.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the drive detects a LoG [Com Error / Abnormal SD card].
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the motor is started and during DC Injection Braking.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the motor is stopped and during DC Injection Braking.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when motor 3 is selected.
ON : Motor 3 Selection
OFF : Motor 1 or Motor 2 Selection
V/f CL-V/f OLV CLV AOLV
Generates inverse output of the function for the selected MFDO. Sets the function for
which to generate inverse output with the last two digits of 1xx.
Description
V/f CL-V/f OLV CLV AOLV
Sets the input signal level for MFAI terminal A1.
0 : 0 to 10 V (Lower Limit at 0)
1 : -10 to +10V (Bipolar Reference)
V/f CL-V/f OLV CLV AOLV
Selects a function assigned to the MFAI terminal A1.
YASKAWA ELECTRIC SIEP C710617 19A YASKAWA AC Drive CR700 Technical Manual
Description Ref.
680
680
680
199
203
680
680
680
680
681
681
681
682
682
682
193
203
682
Default
(Range)
0
(0, 1)
0
(0 - FF)