Iq18 Dadf Lead Edge Offset Rap - Xerox WorkCentre 4150 Service Manual

IQ18 DADF Lead Edge Offset RAP

Use this RAP when copies from the DADF have lead edge offset.
Procedure
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Go to the relevant procedure:
• 4150 Checkout
• 4250/4260 Checkout
• 4265 Checkout
4150 Checkout
Refer to Wiring Diagram 11. Perform the following:
1. Open the DADF top cover assembly,
2. Check the document path for damage or obstructions.
3. Check that the following components are clean and rotate freely.
• Registration roll, PL 5.15 Item
• Registration roll idlers, PL 5.15 Item
4. Check that the registration sensor actuator,
aged.
5. Enter dC330 code 05-130. Check the registration sensor (Q05-130),
necessary, install a new registration sensor,
6. Enter dC131 code 05-100. Adjust the offset as necessary.
7. If the defect is still present, install a new document transport assembly,
4250/4260 Checkout
Refer to Wiring Diagram 29. Perform the following:
1. Open the DADF top cover assembly,
2. Check the document path for damage or obstructions.
3. Check that the following components are clean and rotate freely.
• Transport idlers, PL 5.45 Item
• CVT roll, PL 5.50 Item 19.
• CVT roll upper idlers, PL 5.40 Item
• CVT roll lower idlers, PL 5.35 Item
4. Check that the registration sensor actuator,
aged.
5. Enter dC330 code 05-130. Check the registration sensor (Q05-130),
necessary, install a new registration sensor,
6. Enter dC131 code 05-100. Adjust the offset as necessary.
7. If the defect is still present, install a new document transport assembly,
4265 Checkout
Refer to Wiring Diagram 45. Perform the following:
1. Open the DADF top cover assembly,
WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
WARNING
PL 5.15 Item 11.
21.
28.
PL 5.15 Item 12 moves freely and is not dam-
PL 5.15 Item
PL 5.15 Item 14.
PL 5.15 Item
PL 5.30 Item 2.
11.
15.
8.
PL 5.40 Item 18 moves freely and is not dam-
PL 5.40 Item
PL 5.40 Item 17.
PL 5.30 Item
PL 5.30 Item 2.
2. Check the document path for damage or obstructions.
3. Check that the following components are clean and rotate freely.
• Transport idlers, PL 5.45 Item
• CVT roll, PL 5.50 Item
• CVT roll upper idlers,
• CVT roll lower idlers,
4. Check that the registration sensor actuator,
aged.
5. Enter dC330 code 05-130. Check the registration sensor (Q05-130),
necessary, install a new registration sensor,
6. Enter dC131 code 05-100. Adjust the offset as necessary.
7. If the defect is still present, install a new document transport assembly,
14. If
1.
17. If
26.
January 2016
3-21
11.
19.
PL 5.40 Item 15.
PL 5.35 Item 8.
PL 5.40 Item 18 moves freely and is not dam-
PL 5.40 Item 17.
PL 5.40 Item 17. If
PL 5.30 Item 26.
Image Quality
IQ18