Xerox WorkCentre 5222 Service Manual page 1225

Chain-
Link Content
790-630 Virtual Address Book
790-631 Address Book NVM Data Transfer To New
HDD
Chain 790-xxx Copy Service
Chain-
Link Content
790-600 Poster Overlap Width
790-605 Sample Copy Enable
790-606 Annotation Page No-Pattern
790-607 Annotation Page No-Position
790-609 Annotation Page No-Position_Side2
790-611 Annotation Date-Position
790-613 Annotation Date-Position_Side2
790-614 Annotation Stamp-Position
790-617 Annotation Stamp-Density
790-618 Annotation Stamp-Position_side2
790-619 Annotation Stamp-dirCheck
790-620 Allover Copy Enable
790-632 Added Thumbnail Default Net
790-633 Added Thumbnail Default Mail
790-639 Default Copy - Staple Position Information
790-640 Paper Change Display
790-641 Paper Color Display
790-642 Paper Information Display
790-661 Report Store Box ID
790-662 Consumable Auto Display Timing
790-664 Address Book Import Mode
790-665 Default Display Tray Setting
790-666 Display DADF FAX Read Mode
General Procedures
Table 9 UI
Default Range
0 0~6
0 0~1
Table 10 Copy Service
Default Range
10mm 1~25
0: Disable 0~1
1 1~6
6 1~6
0 0~1
5 1~6
0 0~1
2 1~9
0 0~2
1 0~1
1 0~1
1 1~2
1 0~1
0 0~1
Automatically set at the 0~255
time of initiation
0 0~255
1 1~1
1 0~255
1 1~500
0 0~2
0 0~1
1 0~1
1 0~1
February, 2008
6-86
Meaning
0: Address Book 3: 3-digit Virtual Address Book 4: 4-digit Virtual Address Book 5: 5-
digit Virtual Address Book 6: 6-digit Virtual Address Book (* Settings 1 and 2 are not
allowed)
0: Do not transfer 1: Transfer
Meaning
10mm~25mm
0: Disable, 1: Enable
1: N, 2: -N-, 3: Page N, 4: N/M, 5: -N/M-, 6: Page N/M
1: Top Left, 2: Top Right, 3: Top Center, 4: Bottom Left, 5: Bottom Right, 6: Bottom Center
0: Opposite to Side 1, 1: Same as Side 1
1: Top Left, 2: Top Right, 3: Top Center, 4: Bottom Left, 5: Bottom Right, 6: Bottom Center
0: Opposite to Side 1, 1: Same as Side 1
1: Top Left, 2: Top Right, 3: Top Center, 4: Bottom Left, 5: Bottom Right, 6: Bottom Center, 7:
Left Center, 8: Right Center 9: Center
0: 0% (solid), 1: [25%], 2: [50%]
0: Opposite to Side 1, 1: Same as Side 1
0: Set for first sheet, 1: Set for each sheet
1: Do not copy whole image (copy all with reduction), 2: Copy whole image
0: Do not add, 1: Add
0: Do not add, 1: Add
Logical OR of the following:
0x01: Single at left trail edge
0x02: Single at right trail edge
0x04: Single at center trail edge
0x08: Dual at center trail edge
0x10: Quad at center trail edge
0: Do not display, 1: Display
1: Display
0: Do not display, 1: Display applied size, 2: Display hole-punch attribute
Box Number
0: Do not display, 1: Display only when system becomes ready after power is turned on and
initialization sequence completes, 2: Display each time auto clear occurs
0: Addition mode, 1: Replacement mode
0: Disable, 1: Enable
0: Do not display, 1: Display
Launch Version
WorkCentre 5225, 5230