Stacking Component Codes; Input Component Control Codes Iot - Xerox WorkCentre 5222 Service Manual

Stacking Component Codes

NOTE: Some components cannot be energized at the same time as another component. If you
activate such a combination of components, the first component switched on will be automati-
cally switched off.
1. When perform multiple component checking. input new Chain-Link number after one (or
several) component(s) is (are) in operating.
NOTE: Only latest Chain-Link number indicates.
Chain-Link Name
010-100 EXIT SENSOR
010-101 EXIT SENSOR1(EXIT)
010-200 Fuser Control Sensor FS1
010-201 Fuser Control Sensor FS2
012-100 Transport Entrance Sensor
012-110 Registration Clutch ON
012-111 IOT Exit Sensor
012-140 Entrance Sensor
012-150 Compile Exit Sensor
012-151 Compile Tray No Paper Sensor
012-190 H-Transport Ent. Sensor
012-191 H-Transport Exit Sensor
012-220 Front Tamper Home Sensor
012-221 Rear Tamper Home Sensor
012-240 Stapler Move Home Sensor
012-241 Stapler Move Position Sensor
012-242 Low Staple Sensor
012-243 Self Priming Sensor
012-244 Staple Home Sensor
012-250 Eject Clamp Home Sensor
012-251 Set Clamp Home Sensor
012-252 Eject Home Sensor
012-260 Upper Limit Sensor
012-262 Stacker No Paper Sensor
012-263 Stack Encoder Sensor
012-264 Stack Height Sensor 1
General Procedures
Component Control
Table 1 Input Component Control Codes IOT
Connector
Level Meaning
L with paper
H with paper Sensor level detected by EXIT MODULE
Analog Min 0, Max 1023
Analog Min 0, Max 1023
H with paper (M1-1); without paper (M1-1.5)
H IOT Regi Clutch OFF (A-Finisher, B/C-Finisher); IOT Regi Clutch ON (SB-
Finisher)
H with paper (A-Finisher, B/C-Finisher); without paper (SB-Finisher)
H with paper
H with paper (A-Finisher, B/C-Finisher, SB-Finisher M1-1)
H with paper (B/C-Finisher)
H with paper
H with paper
H home position (B/C, SB-Finishers); other than home position (A-Finisher)
H home position (B/C, SB-Finishers); other than home position (A-Finisher)
H other than home position
H other than home position (B/C-Finisher); Stapler Unit position detection (SB-
Finisher)
H without staples (A, B/C-Finishers); without/low staples (SB-Finisher)
H staple not ready (A, B/C-Finishers); staple ready (SB-Finisher)
H other than home position
H other than home position
H other than home position
H other than home position
H upper limit position
H without paper (B/C-Finisher)
H Encoder pulse detected
H paper detected (C-Finisher)
February, 2008
6-124
2. When confirm the status of another component still in progress, select Enter Number then
input Chain-Link number of applicable component.
3. Select Stop key after confirming.
Stop operation of component indicated on screen.
NOTE: There are no Cyclic Component in below category:
• IIT Input Component.
• IIT Output Component.
• IOT Input Component.
Remarks
Not Available
EXIT
Standby temperature monitor
Standby temperature monitor
Not Available
Not Available
Not available
Not Available
SB-Finisher:
Before Sensor change: H with paper
After Sensor change: H without paper
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
uppermost position of Stacker Tray
detected (no paper) (SB-Finisher)
Stacker Tray position detected (SB-Fin-
isher)
Launch Version
WorkCentre 5225, 5230