Xerox WorkCentre 5222 Service Manual page 1172

Chain-Link Content
710-609 Alternate Size Set9
710-610 Alternate Size Set10
710-611 Alternate Size Set11
710-612 Size-Mix Mode Size Orientation
710-613 Mixed Size Selection
Chain 715-xxx IISS
Chain-Link Content
715-017 IIT Fail Bypass
715-018 Fan Control Mode
715-020 Number of APS
715-022 Lamp Fan Fail Bypass
715-023 Lamp Fan On Time (Low Rotation)
715-024 Lamp Fan Off Time
715-025 FL Timer Set
715-026 Lamp ON Interval
715-027 Lamp ON Time
715-030 IIT Failure Part Diagnosis
715-050 Platen SS Registration Adjustment
715-051 Platen SS Reduce/Enlarge Adjustment
715-052 Platen Glass Type
715-053 Platen PRadjF
715-056 CVT FS Offset Side1-1 (139.7-148)
715-057 CVT FS Offset Rear Side2-1 (139.7~148)
715-058 CVT FS Offset Side1-2 (182-194)
715-059 CVT FS Offset Side2-2 (182-194)
715-060 CVT FS Offset Side1-3 (203.2)
715-061 CVT FS Offset Side2-3 (203.2)
715-062 CVT FS Offset Side1-4 (210)
715-063 CVT FS Offset Side2-4 (210)
Launch Version
WorkCentre 5225, 5230
Table 1 DADF
Default Range Meaning
0 0~2 PF1: Switches between 8x10S and 8x10.5S. No-Mix: Inch13/Inch14,0: Default,1: 8x10S,2: 8x10.5S
PF2: Switches between 8x10S and 8x10.5S. No-Mix: Inch13/Inch14,0: Default,1: 8x10S,2: 8x10.5S
0 0~2 PF1: Switches between B5L and 16KL. Size-Mix: mm,0: Default,1: B5L,2: 16KL PF2: Switches
between B5L, 16KL and 8.5x11L. Size-Mix: mm,0: Default 1: B5L,2: 16KL 3: 8.5x11L PF2 setting
range is 0~3.
0 0~3 PF1: Switches between B5S/16KS/8.5x11S. Size-Mix: mm, 0: Default, 1: B5S, 2: 16KS, 3: 8.5x11S
1 0~1 Switches between LEF and SEF.,0: LEF,1: SEF
1 0~1 Switches the size (standard size/non-standard size) to be transmitted from DADF to IISS in mixed
size mode of fax job. 0: Non-standard size mode, 1: Standard size mode
Table 2 IISS
Default Range Meaning
0 0~1 0: Fail Bypass Off, 1: Fail Bypass On
0 0~1 0: Normal, 1: Extended mode
1 0~1 0: 1 APS, 1: 2 APS
0 0~1 On/Off of Lamp Fan Fail Detection. 0: On, 1: Off
15 0~60 Time period to operate Lamp Fan at low rotation (value can be set in 1-minute increments)
0 0~60 Time period during which Lamp Fan stops (value can be set in 1-minute increments)
0 0~1 0: Standard FL Timer settings (30min rest/0.5sec On), 1: Condensation mode setting (Diag 715-
026, 715-027 timer settings apply)
30 1~60 Interval setting (time between Lamp OFF and Lamp ON again) (unit: min.)
1 1~60 Lamp ON time setting (unit: sec.)
0 0-65535 By writing 1, diagnosis for IIT failed part starts. The numbers of failed parts that are predicted to read
this NVM are displayed after the failed parts diagnosis ends. When Fail occurs during the failed
parts diagnosis, Fail code is recorded in this NVM and the failed parts diagnosis ends. Even when 1
is entered, the value is not actually written. When values other than 1 are entered, the values are
invalid.
100 16~184 Slow Scan Direction Regi Correction Value (0.036mm/increment), Factory Settings
50 44~56 Slow Scan Direction Regi Correction Value (0.1%/increment), Factory Settings
2 0~2 0: Platen model, 1: Belt DADF, 2: CVT, Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (Dot), VLSS=PROMVLSS+(PRadjF-120)x2, Factory Set-
tings
120 0~240 Fast Scan Direction Regi Correction Value (2dot/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (2dot/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (2dot/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (2dot/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (2dot/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (2dot/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (2dot/increment) in CVT. Factory Settings
120 0~240 Fast Scan Direction Regi Correction Value (2dot/increment) in CVT. Factory Settings
February, 2008
6-33
General Procedures
IIT NVM List