Xerox WorkCentre 5222 Service Manual page 1264

Chain-Link Name
012-265 Stack Height Sensor 2
012-267 Stacker Height Sensor
012-268 Stacker Stock A Sensor
012-269 Stacker Stock B Sensor
012-271 Puncher Home Sensor
012-274 Puncher Encoder Sensor
012-275 Punch Box Set Sensor
012-277 Puncher Detect
012-278 Stacker Stock A Sensor
012-279 Stacker Stock B Sensor
012-280 Compiler Cover Safety Switch
012-300 Eject Cover Switch
012-301 Eject Cover Switch
012-302 Finisher Front Cover Switch
012-303 H-Transport Interlock Sensor
013-101 Booklet Knife Home Sensor
013-107 Booklet Low Staple Front Switch
013-108 Booklet Low Staple Rear Switch
013-141 Booklet Staple Cam Front Switch
013-142 Booklet Staple Cam Rear Switch
013-143 Booklet Staple Move Home Sensor
013-144 Booklet Staple Move Position Home Sen-
sor
013-160 Folder Detect
013-161 Booklet Detect
013-300 Booklet Cover Open Switch
013-301 Booklet Safety Switch
047-200 FACE UP TRAY DETECTED
047-201 OCT2 DETECTED
047-205 OCT1 HOME POSITION SENSOR
047-206 OCT2 HOME POSITION SENSOR
071-100 FEED OUT#2 SENSOR
071-101 T/A F/O3 SENSOR
071-102 T/A F/O4 SENSOR
071-105 DUP WAIT SENSOR
071-106 T/A F/O3 SENSOR
071-107 T/A F/O4 SENSOR
Launch Version
WorkCentre 5225, 5230
Table 1 Input Component Control Codes IOT
Connector
Level Meaning
H paper detected (C-Finisher)
H Stacker Tray paper detection
H Stacker Tray position detection
H Stacker Tray position detection
H home position (C-Finisher); other than home position (SB-Finisher)
H Puncher Encoder pulse detected
H Box is seated (C-Finisher); Box is not seated (SB-Finisher)
H Puncher Unit is not detected
H Stacker Tray position detection (With Light Shield Plate)
H Stacker Tray position detection (With Light Shield Plate)
H Compiler Upper Chute open
H Eject Cover is open (B/C-Finisher); Eject Cover is closed (SB-Finisher)
H Eject Cover is closed (B/C-Finisher); Eject Cover is open (SB-Finisher)
H Finisher Front Cover is open
H H-Transport is open
H other than home position
H low staples or Staple Cartridge pulled out (C-Finisher); with staples (SB-Fin-
isher
low staples or Staple Cartridge pulled out (C-Finisher); with staples (SB-Fin-
isher
H Front Booklet Stapler Head is not in home position
H Rear Booklet Stapler Head is not in home position
H Booklet Stapler Unit is in home position
H Staple position of Booklet Stapler Unit is detected
H Folder Unit is detected
H Booklet Unit is detected
H Cover is open
H Normal
L Detected
L Detected
L OCT1 is at its home position
L OCT2 is at its home position
L with paper
L with paper
L with paper
L with paper
L with paper Hot-Line Control
L with paper Hot-Line Control
February, 2008
6-125
Remarks
Stacker Tray position detected (SB-Fin-
isher)
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
Not Available
L = obstruction detected
EXIT
EXIT
EXIT
EXIT
Not Available
Not Available
Not Available
DM
Not Available
Not Available
General Procedures
Component Control