Table of Contents
Advertisement
dummyhead
dummyhead
FRONT WHEEL/SUSPENSION/STEERING
SERVICE INFORMATION
GENERAL
• When servicing the front wheel, fork or steering stem, support the motorcycle using a safety stand or hoist.
• A contaminated brake disc or pad reduces stopping power. Discard contaminated pads and clean a contaminated disc with a
high quality brake degreasing agent.
• Do not operate the brake lever and pedal after removing the caliper and front wheel.
• After the front wheel installation, check the brake operation by applying the brake lever.
• Use only tires marked "TUBELESS" and tubeless valves on rim marked "TUBELESS TIRE APPLICABLE".
• For brake system information (page 19-5).
SPECIFICATIONS
Minimum tire tread depth
Cold tire
Driver only
pressure
Driver and passenger
Axle runout
Wheel rim runout
Wheel balance weight
Fork
Spring free
length
Tube runout
Recommended fork fluid
Fluid level
Fluid capacity
TORQUE VALUES
ITEM
Handlebar holder bolt
Handlebar switch housing screw
Front master cylinder holder bolt
Handlebar weight mounting screw
Front brake disc mounting bolt
Front axle
Front axle pinch bolt
Fork socket bolt
Bottom bridge pinch bolt
Fork cap
Top bridge pinch bolt
Front brake caliper mounting bolt
Steering stem adjusting nut
Steering stem adjusting lock nut
Steering stem nut
Clutch lever pivot bolt
(NC700X/XA/S/SA)
Clutch lever pivot nut
(NC700X/XA/S/SA)
17-8
ITEM
Radial
Axial
NC700X/XA/XD
NC700S/SA/SD
NC700X/XA/XD
NC700S/SA/SD
NC700X/XA/XD
NC700S/SA/SD
THREAD
Q'TY
DIA. (mm)
4
8
4
5
2
6
2
6
5
8
1
18
1
8
2
8
2
10
2
37
2
8
2
8
1
26
1
26
1
24
1
6
1
6
STANDARD
–
2
250 kPa (2.50 kgf/cm
, 36 psi)
2
250 kPa (2.50 kgf/cm
, 36 psi)
–
–
–
–
394.9 (15.55)
357.0 (14.06)
–
Honda ULTRA CUSHION OIL 10W or
equivalent
104 (4.1)
103 (4.1)
3
514 ± 2.5 cm
(17.4 ± 0.08 US oz, 18.1 ±
0.09 Imp oz)
3
518 ± 2.5 cm
(17.5 ± 0.08 US oz, 18.2 ±
0.09 Imp oz)
TORQUE
N·m (kgf·m, lbf·ft)
22 (2.2, 16)
2.5 (0.3, 1.8)
12 (1.2, 9)
10 (1.0, 7)
ALOC screw; replace with a new
one.
42 (4.3, 31)
ALOC bolt; replace with a new one.
74 (7.5, 55)
Apply grease to the sliding surface.
22 (2.2, 16)
20 (2.0, 15)
Apply locking agent to the threads.
39 (4.0, 29)
22 (2.2, 16)
22 (2.2, 16)
30 (3.1, 22)
ALOC bolt; replace with a new one.
23 (2.3, 17)
See page 17-38
Apply engine oil to the threads.
–
See page 17-38
103 (10.5, 76)
See page 17-38
1.0 (0.1, 0.7)
Apply grease to the sliding surface.
6.0 (0.6, 4.4)
Unit: mm (in)
SERVICE LIMIT
1.5 (0.06)
–
–
0.2 (0.01)
2.0 (0.08)
2.0 (0.08)
60 g (2.1 oz)
max.
387.0 (15.24)
349.9 (13.78)
0.20 (0.008)
–
–
–
–
–
REMARKS
Advertisement
Table of Contents
Troubleshooting
